【正文】 equency acceleration gainUser alarm timeDRV delay timeUPF delay timeX1 delay timeX2 delay timeTorque detect 1Torque detect 29OPTION CARDSOption Cards: Only one option card can beused.1. Relay output cardPart Number: CF31005101Relay to outputRY1Terminal blockR1CR1BR1AR2CFunction: The open collector output signal is convertedinto the dry contact signal. Parameters E25 and E26can be used.Contact rating: 230 VAC, 1A。 1% (Motor torque: Within 177。 11: FRQ down12: Catch on the FlySame as aboveSame as aboveSame as aboveSame as aboveSame as above~3000。 1。 1: FWD only provided2: REV only provided3: FWD/REV not provided4: (future)~~ () V~~0: End1: Resistance only2: Full tuning~~0: Linear acceleration。 1: SCurve accelerationSetting Unit––FactoryDefault0: Local 0:00Hz0: Linear accelerationRef.pg.35Basic parameters0708A091011121314151600010203040506070809101112~0: Constant torque1: Decreasing torque2: Brokenline V/Hz~%~~ () V0: Local1: VRF 5V2: VRF 8V, 3: VRF 10V4: IRF 200mA~~~ () V0: FWD/REV provided1: REV not provided。C when installed inside the panel) Note 410176。 10176。5%10 Approx. 10%Braking resistor150% or greater, short duty cycleOpen Note 6Forced air cooling911NEMA115Braking Torque Power Supply2016Note 1: Rated output voltage is 220 V. 2: The ratio (%) to the rated current of the inverter. 3: The maximum output voltage will not exceed the supply voltage. Any desired voltage smaller than the supply voltage can be set. 4: If an AC line reactor (AC/DC: option) is used. 5: The braking torque and the operation rate are subject to the braking unit and braking resistor used. 6: UL Approved in open chassis only (enclosure same as all other models).400V classTypeApplicable motor output (kW)Rated capacity (kVA) Note 1OutputRated current (A)Rated overload current Note 2Rated voltage (V) Note 3Braking Torque Power SupplyAF3124 AF3124 AF3124 AF3124 AF3124 AF3124 AF3124 AF3124 AF3124 AF31245A5U 7A5U 011U 015U 022U 030U 037U 045U 055U 075U 1013131619242432364861739686112115150 486480150% 1 min。%? 120:1 Constant Torque Speed Range [Sensorless Vector Mode)? Sensorless Vector Control Mode? Volts/Hertz Mode102030405060 [Hz]150100500? Closed Loop Vector Mode (1000:1 Constant Torque Speed Range)? 250% Maximum Starting Torque (Vector Mode)? Highperformance Autotuning? Multimotor (Bmode)? IGBT Technology? 16 Preset SpeedsTorque [%]2001000 12345678910 [Hz]CONTENTSSpecifications . . . . . . . . . . . . . . . . . . . . 2, 3Operation Unit (OPU) . . . . . . . . . . . . . . . . 4Display . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Parameter Menus . . . . . . . . . . . . . . . . . 69Option Cards . . . . . . . . . . . . . . . . . . . 10, 11Options and Peripheral Equipment. . . 12, 13Connection Diagram . . . . . . . . . . . . . . . . 14Terminal Functions . . . . . . . . . . . . . . . . . 15Outside Dimensions. . . . . . . . . . . . . . 16, 171SPECIFICATIONS200V classTypeApplicable motor output (kW)Output Rated capacity (kVA) Note 1 Rated current (A)Rated overload current Note 2Rated voltage (V) Note 3Phase/voltage/frequencyVoltage amp。 380Vand 400~420V/50Hz。 operation voltage, 030%.,000 sec。C can be achieved by removing the front cover if the equipment is installed inside an enclosure. 5: The base is the speed (rpm) at the base frequency.3OPERATION UNIT (OPU)DisplayEasy to read LCD display.Two lines, 16 Characters(English and Japanese).Data/MenuThis key is used for changingthe position of the data/menucursor.“READY” (Green)AF3100α is ready foroperation when illuminated.SetAfter setting respective data,press this key and the displayvalues are written to memory.“ALARM” (Red)When illuminated a faultcondition exists.CursorThis key is used to move thecursor to the digit to bechanged.“LOCAL” (Green)AF3100α is controlled by theOPU/keypad when illuminated.Up / DownThis key is used to change theoperation frequency, name ofparameter, and data.: Increase: DecreaseForward RotationForward operation start key.The start key is pressed, runlamp turns ON。 1: Provided~%~%~%~% ~ Inverter rated current0:4P, 1: 6P0: Generalpurpose motor 11: Generalpurpose motor 22: Generalpurpose motor 33: AF motor 1。 3: Automatic432: BrokenlineV/Hz % () V%%% ()V0:FWD/REVPROVIDED4344454443D080910111213Note: The menus C14 and C15 are displayed and can be set only when the control method selection C12 is set to 1: Sensorless.*: Differs according to the rated capacity.7PARAMETER MENUSMenu00010203040506FunctionOutput frequency detection 1Output frequency detection width 1Frequency counteroutput selectionFrequency counter scaleFrequency counter correctionCustom display mode unitCustom display mode multiplierDisplayFrequency detection 1Frequency detection width 1Frequency meter selectionFrequency meter scaleFrequency meter correctionCustom display modeAvailable Choices~~0: Analog 1。 5: Motor torque6: Frequency 2Same as above~%~%~%~%0: Fault。 1: English0: Local。 3: 010V, 4: 020maFactory Setting 1024 0100%100% 70%0Settings for Analog Monitor Output Signals for AM1 and AM2. Refer to parameters E19 and E20.Setting 0 123456Signal Description Output frequencyCommand frequencyOutput currentOutput voltageOverload rate Motor torqueOutput speed