【正文】 1 is OK0335,FF2Z0007161,60000073902, B,DCJ300201P, B,FF2Z0007161Power Supply 2 is faulty0335,FF2Z0007176,60000073902, B,DCJ300201P, B,FF2Z0007176switch:admin6. tempShow查看交換機的環境溫度Enter the tempShow mand:switch:admin tempshowIndex Status Centigrade Fahrenheit1 OK 21 702 OK 22 723 OK 29 844 OK 24 755 OK 25 77switch:admin7. errDump、errShow、errClear查看交換機的內部消息日志To display the system message log, with no page breaks Enter the errDump mand.To display the system message log one at a time Enter the errShow mand.To clear the system message log Enter the errClear mand.8. supportShow、supportSave、pdShow收集交換機的診斷數據supportShow 顯示診斷信息和狀態信息supportSave將數據打包、上傳至指定的FTP服務器The mand prompts for an FTP server, packages the following files, and sends them to the specified server:? The output of the supportShow mand? The contents of any trace dump files on the switch? System message logs (for Brocade directors, supportSave saves the system message logsfrom both of the CP blades)pdShow 顯示panic dump文件的內容，幫助診斷系統panic的原因9. nsShow、nsAllShow、fabricShow檢查連接到交換機的設備nsShow 顯示連接到交換機的所有設備nsAllShow 顯示連接到Fabric的所有設備fabricShow 顯示Fabric中的所有交換機10. licenseShow、wwn檢查license文件和交換機的WWN號11. version檢查Fabric OS的版本，將顯示如下信息： Kernel: displays the version of switch kernel operating system. Fabric OS: displays the version of switch Fabric OS. Made on: displays the build date of firmware running in switch. Flash: displays the install date of firmware stored in nonvolatile memory. BootProm: displays the version of the firmware stored in the boot PROM.12. haShow查看Control Blade的狀態swDir: admin haShowLocal CP (Slot 6, CP1): Active Remote CP (Slot 5, CP0): Standby HA Enabled, Heartbeat Up, State Synchronized13. slotShow查看各個Blade的狀態14. portCfgSpeed修改端口的速率15. portEnable或portCfgPersistentEnableReset端口16. 檢查WWN卡狀態下列命令如果不能正確執行，則說明WWN卡需要更換：，chassisShow：顯示交換機的WWN號chassisShow：顯示chassis和WWN卡的狀態ipAddrShow，ipAddrSet：顯示CP Blades的IP地址historyShow、historyLastShow：顯示歷史日志信息switchName：顯示交換機的名字修改Domain ID1. 查看當前的Domain ID輸入命令fabricShow，輸出結果中的Switch ID即包括交換機的Domain ID。switch:admin hashowLocal CP (Slot 5, CP0): Active, Warm RecoveredRemote CP (Slot 6, CP1): Standby, HealthyHA enabled, Heartbeat Up, HA State synchronized7. 升級Firmware如果SAN交換機支持HA，則使用命令firmwareDownload，同時升級主備Control Blade。必須在線更換CP Blade，才能實現配置信息的自動同步。使用命令haFailover，實現CP Blade間的手動切換。4. 將CP Blade上的電源開關撥至Up位置，給CP Blade供電。一個zone可以同時屬于不同的zone configuration之中。 2,34。 4,6。 array1。 configuration (yes, y, no, n): [no] yzone config USA_cfg is in effectUpdating flash ...