【正文】 erial.5. 外觀： Appearance: 1)所有圓角半徑和脫模斜度按照Pro/e 3D Data。 Package and Transport: Product should be packaged independent, and lay in tray, finally put the trays in the paper box。 Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the Qualification stage.。 Package of product should be quantitative, sealed, dustless and dampproof .04. BATTERY。4. 螺絲孔做(不做)銅化處理。放置屏蔽罩時，罩內元件限高； (No Shielding)指可以放置屏蔽罩區域。澆口凸出≤。 標有環形圈的是重點尺寸,每批次出貨均需檢查,Qualify時需要做CP/CPK；: Specified dimensions in the drawing are used to check outside shape, function and assembly。 外觀皮紋: VDI 24。 Unspecified dimensions refer to Pro/e 3D model data。文件類型文件編號版本結構2D NOTE頁數有效期限保密級管理辦法28/282005/07/01—2008/07/01保密德信無限通訊科技(上海)有限公司TechFaith Wireless Communication Technology (Shanghai) Co.,LTD.結構2D圖 技術標注參考規范文件編號 ：QC1001保密等級 ：保密文件類型 ：管理辦法有效期 ：3年頁數 ：1/28版本 : 編制日期 ：2004/05/24開始執行日：2005/07/01NO編制/變更日期變更理由變更內容版本編制/修改人批準12004/05/24新編沈林王迅22006/01/04修改將2D標準樣板圖中技術標注更新到本文件中蔣偉鵬丁勇目錄索引01. Latch02. Antenna PCBA limited drawing PCBA outline drawing04. Battery Lens(注塑) Lens(CNC) Audio cover RF_switch_cover Shielding cover Shielding frame Spring08. Metal dome09. Stop TPU10. Light guide 11. Fpcba 金屬裝飾件 Logo Plating plastic Electroform 雙面膠 泡棉 銅箔 絕緣片 Keypad asm keypad rubber Keypad 電鍍鍵帽 Keypad 數字鍵 外觀漆噴漆圖 導電漆噴漆圖16. Housing part drawing17. Housing Assembly18. Explode01. Latch技術要求（Notes）:1. 材料：POM Dupont500, 用100%原材料。 Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the Qualification stage.3. 公差：未注公差依照?qǐng)D面公差表。 Appearance：Product should be tidy and purity, no nick, no shrinkage and other blemish。返回索引目錄 Unspecified round: 。穴號應刻在模具上，標志不得高于表面。不放置屏蔽罩時元件限高； Limiting Height for shielding area is only for electronic ponets inside , not including shielding and the mechanical electronic ponents been included in this drawing。 Screw hole is PTH（NPTH） type. PCBA outline drawing1. 圖面尺寸用于檢驗PCB外形、功能和裝配。Using double adhesive between battery rear cover and cell。 Batt_conn must be gilt, coating thickness must be no less than 鹽霧試驗：35℃，5% 氯化鈉溶液，48小時后無腐蝕。： Product should be satisfied with quality standard of Techfaith Wireless: 《部品檢驗標準_注塑件》V 。 Round and draft should ply with Pro/e 3D Data 2)未注脫模斜度為1度,。 Package and Transport: Product should be packaged independent, and lay in tray, 返回索引目錄 finally put the trays in the paper box。 LENS transparent area should be checked in black background, no flaws. 2)印刷部分要求色彩均勻、無劃傷、黑白點、瑕疵。3SHA，用100%原材料。 Unspecified dimensions refer to Pro/e 3D model data。 外觀皮紋: VDI 21。 Dimension: Specified dimensions in the drawing are used to check outside shape, function and assembly。 Package and Transport: package by chain bags and lable the quantity. 07. Shielding、spring. Shielding_cover: SUS304(不銹鋼),T=。: Unspecified tolerance should ply with tolerance table in the drawing。: C7521(cupronickel),the material have the well performance of welding , any two point39。: Unspecified tolerance should ply with tolerance table in the drawing。s spring is , the largest press is .：見參數表； of spring: see the table of parameter。 公差：未注公差依照?qǐng)D面公差表。外型及DOME位置公差為:177。3 SHA,with 100% raw material .: 圖面尺寸用于檢驗零件外形、功能和裝配。 Tolerance:Unspecified tolerance should ply with tolerance table in the drawing。 Mark of ejection pin should be lower than product surface。 Unspecified tolerance should ply with tolerance table in the drawing。返回索引目錄 Cavity NO. should be carved on mould,Marking could not be above surfaces。 The vertex of the rightangle indicate the center of the b to b conn etc.。: specified dimension in the drawing shall be used to check outside shape,function and assembly。：零件外觀表面附微粘保護膜(3M 3K04)，獨立包裝，放入 托盤對應的凹穴，托盤層堆進紙箱。返回索引目錄 Dimension: Specified dimensions in the drawing are used to check outside shape, function and assembly。 Material: ABS（CHIMEI 757）, in original color and with 100% raw material .2. 尺寸：圖面尺寸用于檢驗零件電鍍后成品外形、功能和裝配； ,未注脫模斜度1度,未注尺寸按照Pro/e 3D Data。4. 外觀：成品清潔、無雜質、無劃傷、縮水及其它瑕疵。 Package and Transport:Product should be packaged independent, and lay in tray, finally put the trays in the paper box。 unspecified draft angle is 10。 product shall be tidy, no grease, no scratch, no sink depressions, no heave. the planeness shall be less than 。雙面?zhèn)潆x型紙，對離型紙形狀有特別要求的在圖中已經畫出該離型紙且標識尺寸。Package and Transport: Product should be packaged with equivalent quantity, and avoid felt from each other。3. 公差:未注公差依照?qǐng)D面公差表；Tolerance: Unspecified tolerance should ply with tolerance table in the drawing。標有環形圈的是重點尺寸,每批次出貨均需檢查,Qualify時需要做CP/CPK。Boundary of part must be smooth amp。5. 包裝與運輸：離型紙廠商出具排版布局圖，按照一定數量封裝，避免褶皺和相互粘結。Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the Qualification stage.2. 材料: 屏蔽材料：COPPER FOIL ,T=（僅單面背膠）。 boundary of part must be smooth amp。標有環形圈的是重點尺寸,每批次出貨均需檢查,Qualify時需要做CP/CPK。Material: Tesa4967, T=。5. 包裝與運輸:零件外觀面需加貼保護膜. and transportation: appearance surface shall be protected by film。 Specified dimensions with marked ring are critical dimensions, need to be checked every shipment, and must do CP/CPK check in the Qualification stage.：未注公差依照?qǐng)D面公差表。:Ni, T=。 飛邊及分型線段差≤,頂桿痕≤。 Dimension: Specified dimensions