英文工程圖紙縮寫(存儲版)
【正文】 air cushion plate 氣墊板 supporting block for location 定位支承塊 located block 定位塊 debrring punch 去毛邊沖子 special shape punch 異形沖子 bending block 折刀 stamped punch 字模沖子 groove punch 壓線沖子 。 hot treatment 熱處理 temper 回火 heating 加熱 preheating 預熱 tempering 回火 hardending /quenching 淬火 annealing 退火 paint coating 金屬涂層噴漆處理 conventional spray painting 傳統噴涂 hot and airless spray painting 熱無氣噴圖 flame spray painting 火焰噴涂 electrostatic spray painting 靜電噴涂 curtain coating 幕式噴涂層 electro coating 電解涂層 roller coating 滾輪涂層 Plating 電鍍 niplaing 電鍍鎳 silver plate 電銀 anodize black 氧化黑 anodize white 氧化白 zincplated 電鍍鋅 sheets/plates 板料 strips 片料 coil 卷料 soft iron 軟鐵 pig iron 生鐵 wrought iron 熟鐵 round iron 圓鐵 scrap iron 費鐵 steel 鋼 crude steel 粗鐵 mild steel,soft steel 軟鐵，低碳鋼 hard steel 硬鋼 cast steel 坩堝鋼，鑄鋼 stainless steel 不銹鋼 hightspeed steel 高速鋼 molded steel 鑄鋼 refractory steel 熱強鋼，耐熱鋼 alloy steel 合金鋼 corrugated iron 瓦垅薄鋼板 angle iron 角鋼 modes of press working die 沖壓模具種類 the singleoperation dies 單工序模具 the poundamp。ALL WELDS CONTINUOUS UNLESS OTHERWISE STATED. 未注焊縫均為連續焊 ALL WELDS 3mm FILLET UNLESS OTHERWISE STATED 未注焊角高 3mm. ALL UNSPECIFIED RADI R3 未注圓角 R3 REMOVE ALL BURRS AND SHARP EDGES 所有尖角 /棱角倒角并去毛 11 TOTAL COILS WORKING COILS HAND WOUND ONLY,END COILS SQUARE TO TOUCH. 總?cè)?shù)約 11 圈；工作圈數約 9 圈；右旋；彈簧的端部磨平以便于接觸 .(此為彈簧技術說明 ) CHANNEL 槽鋼 RSA 708 角鋼 70X70X8 pitch 的錐螺紋 Tackweld 點焊 OD 1/4 outside dimension 1/4的縮寫 外徑直 1/4 75 CRS 尺寸為 75 材質為冷軋鋼板 410 OPENING REF 410 開口參考尺寸 40 REF 尺寸為 40,參考值 BSP ” 圓錐管螺紋 BSPT HEXAGON ” 六角圓錐管螺紋 (即對絲 ) FLAT BAR 扁鋼 TYP 2 POSNS 2 處 FEMALE: 內扣 (母扣 ) MALE: 外扣 (公扣 ) 偏心軸 eccentric shaft 銷軸 PIN 開口銷 COTTER PIN 螺桿 screw 軸承 axletree 擋圈 closing ring 彈性擋圈 circlip 彈簧 SPRING 緊定螺釘 SET SCREW 圓螺母 ROUND NUT 平鍵 FLAT KEY 圓螺母 ROUND NUT 六角螺栓 HEX HD BOLT 無扣長 nonbuckle longth 平墊圈 FLAT WASHER 螺母 FULL NYLOCK NUT 吊環螺釘 LIFTING EYE BOLT 內六角螺釘 SOCKET HEAD CAP SCREW 六角螺釘 HEX HD SETSCREW 軸承隔套 distance sleeve of axletree 深溝球軸承 DEEP GROOVE BALL BEARING 開槽盤頭螺釘 SLOTTED PAN HEAD SCREW 圓錐滾子軸承 TAPERED ROLLER BEARING 推力球軸承 THRUST BALL BEARING 彈簧墊圈 SINGLE COIL SPRING WASHER 縮寫 全稱 翻譯 ACCESS Accessory 附件 ADJ Adjustable,Adjust 調整 ADPT Adapter 使適應 ADV Advance 提 前 AL Aluminum 鋁 ALLOW Allowance 允許 ALT Alternate 改變 ALY Alloy 合金 AMT Amout 數量 ANL Anneal 鍛煉 ANSL Amer Natl Stds Institute APPROX Approximate 大約 ASME Amer Society of Mech Eng
醫療健康相關推薦
鄂ICP備17016276號-1