【正文】 y 11 建立FEWS 4 安裝操作系統 4 安裝SS_FEWS工具包 7 檢查建立好的FEWS 92 安裝前的配置工作（主要在FEWS上完成） 10 物理連線 10 準備軟件 11 創建FSetup配置文件 12 創建missioning session 15[rootfews /] ls /etc/ 17[rootfews /] rm /etc/ 17這里是從FEWS進入MINICOM模式，然后登錄到sm 18 檢查并配置HB/SB/IB/SAB 23 測量文件PM9的大小修改 283 軟件安裝 30 查看FEWS eth0的IP 30 清除CLA的Master Boot Record (MBR) 30 去激活所有SB、IB、SAB 31 同時reset然后去激活兩個MB（CLA0和CLA1） 31 啟動missioning session 32 激活board 1，準備自動安裝CLA0： 32 修改BIOS BIOS設置：ACPI4A板按F4，ACPI2A板按F2 32 保存BIOS退出后系統會提示boot“manually”，敲回車執行，重啟CLA0自動進行軟件安裝 33 CLA0通過DHCP從FEWS獲取IP地址，并下載軟件包進行安裝 33 從FEWS停掉missioning session 34 拔掉FEWS與HB BI P2口的連線 35 檢查當前軟件版本 35 配置8槽的HB 36 配置9槽的HB 38 重啟shelf manager中的DHCP 39 激活I(lǐng)B、SB、SAB 40 檢查IB/SB/SAB是否正常 40 驗證可以從CLA不輸密碼訪問shelf manager， 41 激活CLA1 41 修改BIOS 41 安裝CLA1 42 postConfig finished successfully后在CLA0執行hwcli檢查各個node是否available 43 43 解鎖網元 本次升級一般不涉及 44 開通完成之后的一些設置 441 建立FEWS 安裝操作系統 （開放式虛擬化格式歸檔），F(xiàn)EWS已經具備需要的一些Linux服務和安裝了SS_FEWS工具包。裝好左邊MB后，再通過該MB安裝其余的板件。(沒有實際的物理串口，可以把serial port里的設置清空) 當FEWS運行起來以后，插入U(xiǎn)SB串口，然后使用以下命令檢查USB串口是否被正確地識別：ls /dev/ttyUSB* ，一般情況下USB串口為/dev/ttyUSB0。注：，如有需要重新安裝，安裝過程參考Red Hat相關文檔。要在$PATH環境變量中添加fsetupcli所在目錄，執行如下：export PATH=$PATH:/opt/nokiasiemens/SS_FEWS/bin，即/root/.bash_profile中進行添加，該命令在重啟后不能保存。 TFTP server (available from the Legacy Network Server package) 通過命令chkconfig list可以查看各個運行l(wèi)evel下的服務開通情況但在HIZGGSN402BNk中，查看本機FEWS的dhcp：dhcpd 0:off 1:off 2:off 3:off 4:off 5:off 6:off看似沒有打開，但對完成missioning并沒有影響。BI P2口需要插電口的SFP（SFPCS）。：cat sb_ha_mode=nonhaib_slots=7 10sb_slots=6 11 5 12sab_slots=2 15 3 14 4 13 裝載臨時目錄temp_1，[rootfews /]cd /opt/nokiasiemens/fews/[rootfews fews] mkdir temp_1[rootfews fews] fsetupcli delivery list 檢查是否成功解壓文件:OK [rootfews fews] mount o loop /opt/nokiasiemens/fews/deliveries/用 o loop 選項將某個一般的檔案當成硬盤機分割掛上系統[rootfews fews]cd /opt/nokiasiemens/fews/temp_1/etc/opt/nokiasiemens/ldapfiles/ldif_in [rootfews ldif_in] ls lrt |grep rwxrx 1 root root 1633 Jun 29 17:27 [rootfews ldif_in] cp [rootfews ldif_in] vi 使用vi命令編輯該文件，輸入i，進入編輯模式，完成后退出先按ESC，再輸入“:wq!”保存退出，然后回車即可 (:q! 是不保存退出vi) Choose the mode for the service blades. Allowed values are ha and nonha ha means that there will be session redundancy nonha means that there is no session redundancysb_ha_mode=nonha Select what slots are used for different blade types. Note that slots 1 and 16 are reserved for the management blades and cannot be used Interface blade slots Choose the slots for the interface blades by listing the slots in the ib_slots variable Please use slots 6, 7, 10 and 11 for IB slots. Example: ib_slots=6ib_slots=7 10 Service blade slots Select the slots for service blades by listing the slots in the sb_slots variable HA service blades must be installed as symmetric pairs in slots 7 and 10 6 and 11 5 and 12 4 and 13 3 and 14 2 and 15 Example: sb_slots=7 10 6 11sb_slots=5 6 11 12 Service aware blade slots Select the slots for service aware blades by listing the slots in the sab_slots variable Example: sab_slots=3 14sab_slots=2 3 4 13 14 15 Managed customization blade slots Select the slots for managed customisation blades by listing the slots in the mcb_slots variable Note: if mcb_slots are defined, then ucb_slots cannot be used Example: mcb_slots=2 15mcb_slots= Unmanaged customization blade slots Select the slots for unmanaged customisation blades by listing the slots in the ucb_slots variable Note: if ucb_slots are defined, then mcb_slots cannot be used Example: ucb_slots=2 15ucb_slots= ，驗證其中的部署選項 [rootfews ldif_in] ./ Deployment configuration is valid Summary of created deployment:==============================Number of SBblades : 4 : slot positions: 5 6 11 12Number of SABblades: 6 : slot positions: 2 3 4 13 14 15Number of IBblades : 2 : slot positions: 7 10Number of MCBblades: 0 : slot positions:Number of UCBblades: 0 : slot positions:HA mode : NON_HA ，卸載臨時裝載點temp_1 [rootfews fews] pwd/opt/nokiasiemens/fews[rootfews fews] umount temp_1[rootfews fews] lltotal 16drwxrxrx 3 root root 4096 Apr 21 23:13 deliveriesdrwxrxrx 3 root root 4096 Dec 12 12:59 etcdrwxrxrx 3 root root 4096 Jan 15 18:23 sessionsdrwxrxrx 2 root root 4096 Apr 21 23:21 temp_1[rootfews fews] cd temp_1/[rootfews temp_1] lltotal 0[rootfews temp_1] 創建missioning session my Fsetup配置文件介紹：DELIVERY= 軟件包名字HW_PLATFORM=ATCA 硬件平臺CPU_TYPE=i686 CPU類型TIMEZONE=Asia/Shanghai 時區CLUSTERID=SZHGGSN504BNk 網元名COMM_IFACE=eth0 FEWS 網口名字COMM_FEWSIP=39。 : Q: Please verify password : Q: Please enter password for user 39。具體步驟如下：a）串口登錄active側Shelf manager，先用vi修改/，去掉以上4行前面的“”號，重啟該SHM讓其生效；b） P31/15/3XFP 10G To slot 101/8/110/100/1000 To ASMGRA P11/16/110/100現網有很多沒打開，需要打開，退出的時候會提示saveAMPP1 ethernetAMPP1Eth show port all EKey Admin Physical Physical 。 To slot 161/14/110/100/1000 To slot 61/6/110/100/1000輸入clia user命令，檢查是否有user 3 flexiuser： clia userPigeon Point Shelf Manager Command Line Interpreter 1: Channels 015 Privilege level: Administrator Flags: IPMI Messaging 2: openhpi Channels 015 Privilege level: OEM Proprietary Flags: IPMI Messaging 3: flexiuser Channels 015 Privilege level: Administrator Flags: Link Authentication IPMI Messaging備注：創建命令為 clia user add 3 flexiuser 0x60 4 flexiu7er 刪除用戶 clia user delete x 這個x是 user id 3 退出mini，檢查可配置的硬件進入FEWS系統Terminal環境，檢查可配置的硬件