小型局域網的搭建-免費閱讀
【正文】 在實驗中，我遇到了很多問題，在此回顧一下，避免以后再次犯錯，PC機連接不上時，我很多時候都是忘記了設置網關。之前在從未接觸過的時候很難著手，沒有頭緒。十一：要求企業路由器都允許能進行telnet，VTY密碼是wuyuesicheng，enable密碼是cisco在R2路由器上設置，輸入命名為：wangxinyuanR2enwangxinyuanR2conf tEnter configuration mands, one per line. End with CNTL/Z.wangxinyuanR2(config)line vty ? 015 First Line numberwangxinyuanR2(config)line vty % Inplete mand.wangxinyuanR2(config)line vty 0 15wangxinyuanR2(configline)password wuyuesicheng wangxinyuanR2(configline)exitwangxinyuanR2(config)enable password cciewangxinyuanR2(config) R2的結果如下：在R1上設置，輸入如下命名：wangxinyuanR1enwangxinyuanR1conf tEnter configuration mands, one per line. End with CNTL/Z.wangxinyuanR1(config)line vty 0 15wangxinyuanR1(configline)password ciscowangxinyuanR1(configline)exitwangxinyuanR1(config)enable password cciewangxinyuanR1(config)：在R0上設置，輸入如下命令：RouterenRouterconf tEnter configuration mands, one per line. End with CNTL/Z.Router(config)line vty 0 15Router(configline)password wuyuesichengRouter(configline)exitRouter(config)enable password ccieRouter(config)：十二：要求把企業服務器能夠發布到公網，在R0上設置，輸入下面命令：wangxinyuanR0(config)int fa0/0wangxinyuanR0(configif)ip nat insidewangxinyuanR0(configif)int fa0/1wangxinyuanR0(configif)ip nat outsidewangxinyuanR0(configif)wangxinyuanR0(configif)ip nat inside source static tcp 80 8080如圖：，.（其中有標志hello!world!）在R0上設置，輸入下列命令：wangxinyuanR0(config)int fa1/0wangxinyuanR0(configif)ip nat outsidewangxinyuanR0(configif)exwangxinyuanR0(config)int fa0/1wangxinyuanR0(configif)ip nat insidewangxinyuanR0(configif)：十三： 訪問互聯網，在R0上設置，輸入的命令如下：wangxinyuanR0(config)accesslist 1 permit wangxinyuanR0(config)accesslist 1 permit wangxinyuanR0(config)ip nat inside source list 1 interface FastEthernet1/0 overload：例如：十四：要求對網絡進行訪問控制，在R0上設置，輸入命令為：wangxinyuanR0(configsubif)wangxinyuanR0(configsubif)acc 101 deny ip host wangxinyuanR0(config)int fa0/wangxinyuanR0(configsubif)ip accessgroup 101 inwangxinyuanR0(configsubif)此時，：即不可訪問。十六:。二、實驗環境(實驗設備)硬件：微機軟件：Cisco Packet Tracer二、 實驗原理及內容具體的實驗步驟如下：一：路由器Router0的管理員忘記了密碼，要求你能通過密碼恢復的方式進入路由器斷電重啟路由器，并重啟過程中Ctrl break路由器會進入rommon1這個模式rommon 1confreg 0x2142 rommon 2reset //重啟路由器RouterenRoutercopy startupconfig runningconfigDestination filename [runningconfig]? Routerconf tRouter(config)Router(config)no enable passwordRouter(config)enable password ccieRouter(config)configregister 0x2102Routershow versionRouterwr二：要求給設備命名，命名方式為 你姓名R0,姓
環評公示相關推薦
鄂ICP備17016276號-1