【正文】 amaged and fine. 機柜內所有連接螺釘均應牢固、無松動。 Insulation resistance between MG and CG shall be pliance with GBJ93—86 (more than 5MΩ ) 8) UPS電源測試 UPS Testing: a) 檢查電源盤內和電源開關均處于“ OFF”位置。 Electrican put UPS into use. Measuring voltage delivering to instrument power panel is 220VAC177。 22VAC。 、 12177。 ,12 177。 Checking the reaction of power alarm circuit. 系統啟動、裝載 System starting up and loading. 工程師站起動程序。 各站裝載程序詳見說明書。I圖形式顯示，頁數及畫面內容應符合組態要求。 Width, site, color and inlet or outlet connector of process pipeline. * 測量變量的符號、文字、大小、位置、顏色。 Engineering measurement unit shall ply with design. c) 畫面動態顯示檢查： Active display of screen testing. * 測量變量的變化值應在系統可識別的精度范圍內。 Selecting loop from flow screen and regulating set data, control model (Auto/ manual ) and manual output. 2) 總貌畫面測試 Genera appearance screen testing: a) 確認總貌畫面已按組態數據表組態。 Measuring data, specified data, simulation and digital output are identical. c) 進行改變設定值、控制模式和輸出試驗。 In putting tag No. and finding loop screen. Making sure function of loop type is right. b) 確認測量值、設定值、輸出等正確組態。 Modifying function parameter using engineer keyboard on the screen. Such as, changing regulation para, on line, concept of function, selection of caculation method. 5) 歷史趨勢畫面測試 Testing of history trend screen: a) 確認該畫面已按組態數據表組態。 Making sure operation No, instruction words, priority level is correct. Sound and light classification of different priority level alarm is true. c) 確認任一操作臺上消聲操作均能關閉所有的蜂鳴器。 Operating keyboard directty operated by operator is normal. Finding all indications and operating every loop (including control module, set data, setting series—level, output signal ). Alarming and Executing all functions. 2) 確認由鍵鎖或口令啟動的操作員鍵盤功能操作正常，能改變測量范圍，報警值及輸出信號限制等。 Keep printing time of verifying and resuming identical with actual time. DCS系統調試方案 DCS Test Scheme 4) 檢查如報警發生數量比打印速度快，報警打印不會丟失 Checking alarm—printing can not lose if alarming speed is faster than printing speed. 5) 檢查如打印機發生故障，修復后仍能將這段時間內的報警點正確打印。 Affiring chart can print according to function format. 9) 檢查小時報表、班報表、日報表、月報表的自動打印功能。 After testing function, enecuting accesstesting pletely. Inputing signal from I/O end, observing indication value on operating station CRT, and outputting signal from measuring value. Output deviation allowance shall be pliance with accuracy requirement. ( level) 測試方法：根據回路圖，將輸入輸出信號按模擬量、數字量、熱電偶、熱電阻等類型分組調試 。若不符，檢查順序表組態。 The scheme has mainly introduced the testing for DCS. The testing work process in the pane –chart (chart 3) is general testing so brief introduce inhere. DCS系統調試方案 DCS Test Scheme relevant testing for PLC has other scheme. Testing of auxiliary instrument panel: 對其中的 壓縮機盤主要是調速器、軸瓦溫度監視器、機組 PLC調試。 Checking all series simulation signal and interlock alarming signal between DCS and auxiliary instrument panel. It and first—level test is the heart of plant testing. 確認接口組態正確，檢查串行信號符合設計要求。 First, executing insulation and conductivity test for loop cable. Then, pulsing simulation signal at place of local transmitter and output switch. 2） 在二次聯校過程中，對檢測系統要進一步核對信號的量程、工程 單位、報警上下限等，對調節系統要檢查設定置、比例、積分、微分時間預設定、輸出正反作用及調節閥氣開氣閉是否正確， During the course of inter—testing, checking signal range, unit upper and lower limit of alarming concerning inspecting or testing system time, portion, differential, Checking setting value, portion , time presetting of integral and differential。 施工圖及組態工作單。 4) 在 DCS調試過程中注意： a) DCS調試及運行時應連續供電。 d) 更換組件或卡件時，嚴格按照廠商說明書操作程序進行。 6) 控制室內嚴