成型工藝流程及條件介紹(注塑技術英語大全)-全文預覽
【正文】 mperature is different depending on type of injection molding machine. To protect oil seal of machine it set oil temperature within , If oil seal work on condition that high pressure and damaged It’s work time will be shorter, it can cause molding stable.第三節注射及熔膠(加料)工藝條件設定 ,則射口筒溫度應降低,. 加熱工藝條件設定 ,低速設定一般是在模板接觸的一瞬間,具體位置就設在機臺顯示屏顯示的一瞬間的數字為準,這個數字一般是以這點為標準,即于此點則起不了高壓,高于此點則大,%25%,視乎不同機種而定,壓力一般設定于12%,有些機則可設于515%,也是視乎不同機種不同. ,如果是平面二板模具,快速鎖模段可用較快速度,甚至于用到特快,當用到一般快速時,速度設到5575%,完全平面?？稍O(shè)定到8090%,如果用到特快就只能設定在4555%,壓力則可設定于5075%,位置段視產品的深淺(或長短)不同,一般是開模寬度的1/3. Mold closing: highspeed →lowspeed →low pressure→high pressure Mold closing parameter setting Low pressure high pressure speed 低壓高壓速度 Mold opening parameter: Molding steps: mold opening/closing, heating injection and knocking out. Section 2 Molding parameter Setting 成型工藝參數的設定須根據產品的不同設置. . (2)合模參數 (1).注塑參數 第一節 成型工藝成型工藝流程及條件介紹(注塑技術英語大全)成型工藝流程及條件介紹 In midspeed section: Mold closing speed changes into midspeed after highspeed section finish. Midspeed start position is where two plates meet (include threeplate mold and twoplate mold ) Distance of midspeed is up to distance of two plates plate it speed within 3050% and pressure 2045%. Highpressure section: To normal injection molding machine, highpressure position had been set before they were sent to customer. It can not be modified. For example highpressure position of CHENHSONG machine is speed of highpressure section is about 3035% and higher than that of lowpressure. The pressure is up to mold, it can set within 5585% For fullplate mold, it’s eject air well, it can set pressure 55% .If mold has a lot of slides and flash rate high in production, pressure can set 90%. The proper temperature setting differs depending on type of resin material, but it must be abide by a rule that temperature setting should diminish in step from nozzle to feeding resin material position. ,一般出于對機臺油路中的油封保護需要,油溫最好能控制在40度60度,以免油封長期高壓而變化,縮短使用壽命,造成成型不穩定. Injection Name熔點℃ Mold Temperature(‘c)干燥溫度℃ ,當然也可以依據公式來計算,如公式: Si:注射行程。 Ds:螺桿直徑。 0. 785: value ofΩ/4. Step 2 inject 2/3 of product. It can lower 2/3 of product according to requirement of p
環評公示相關推薦
鄂ICP備17016276號-1