【正文】 od, and chose the UC3825 voltage pulse width modulator. This article lists the DC/DC conversion of the various topologies, makes a parison of the four PWM control modes, analyzes the parallel dual interleaved forward converter’s operating principle and working process, derives in detail and establish the small signal model, designs the pensation work, and carries out the main circuit’s and control circuit’s engineering calculation. Finally, this paper makes the system frequency and time domain simulation, and make some correlation analysis. Key words: dual forward converter, voltage feedback control, small signal model, pensation work, simulation 常州工學院畢業設計論文 II 目 錄 摘 要 ...............................................................................................................................I Abstract ...........................................................................................................................I 目 錄 ............................................................................................................................. II 第 1 章 緒論 ................................................................................................................... 1 開關電源概述 .................................................................................................. 1 本課題研究意義 .............................................................................................. 1 隔離式 DC/DC 變換拓?fù)淞信e ....................................................................... 2 反饋控制模式分類 .......................................................................................... 4 本課題方案研究 .............................................................................................. 7 功率電路選擇 ....................................................................................... 7 控制電路的選擇 ................................................................................... 8 本文研究的主要內容 ...................................................................................... 8 本章小結 .......................................................................................................... 8 第 2 章 功率電路狀態分析及其參數設置 .................................................................. 9 功率電路結構及其工作原理分析 .................................................................. 9 電路結構分析 ....................................................................................... 9 功率電路工作原理分析 ....................................................................... 9 主電路參數設計 ............................................................................................ 14 技術指標 ............................................................................................. 14 功率電路變壓器設計 ......................................................................... 15 主功率開關管的選擇 ......................................................................... 19 二極管的選擇 ..................................................................................... 19 輸出濾波電感 的選擇 ......................................................................... 20 輸出濾波電容的選擇 ......................................................................... 21 本章小結 ........................................................................................................ 21 第 3 章 系統建模與控制電路的設計 ........................................................................ 22 功率電路建模 ................................................................................................ 22 小信號模型的建立 ............................................................................. 22 標準型等效電路的建立 ..................................................................... 25 電壓控制脈寬調制器建模與系統穩態傳遞函數的建立 ............................ 28 常州工學院畢業設計論文 III 電壓控制型開關調節電路原理介紹 ................................................. 28 脈寬調制器的數學模型 ..................................................................... 28 電壓控制系統原始回路穩態傳遞函數的建立 ................................. 29 補償網絡的設計 ................................................................................. 31 控制電路結構 ................................................................................................ 34 UC3825 外圍電路 .............................................................................. 34 主功率管驅動電路 ............................................................................. 36 過流保護電路 ..................................................................................... 37 本章小結 ........................................................................................................ 38 第 4 章 電路仿真 ........................................................................................................ 39 仿真軟件簡介 ................................................................................................ 39 系統時域仿真 ................................................................................................ 40 時域仿真電路及其波形 ..................................................................... 40 時域仿真分析 ..................................................................................... 44 本章小結 ........................................................................................................ 45 結論 .............................................................................................................................. 46 參考文獻 ...................................................................................................................... 47 致謝 .............................................................................................................................. 50 附錄 ................................................................................................................................ 1 常州工學院畢業設計論文 1 第 1 章 緒 論 開關電源概述 隨著電力電子技術的飛速發展，固態化靜止型功率變換電源已經發展成為電力電子技術的三大應用領域之一 (另兩個是“運動控制”和“電力品質控制” )。 此外，其 并聯結構縮小了輸出濾波電感的體積，降低了器件的應力，從