【正文】 2 times/round 25 pcs. 3. Run Tank in different road condition (smooth/rough) 25 pcs. 4. Apply Forward/Reverse/Stop gear change 10 times/round 25 pcs. 5. Apply jump (curb drop) Curb drop 1 time/round (5 cm) 25 pcs. 6. Do the angel climbing in each round 35 degree/1time/round 25 pcs. 7. Apply the impact test in each round Forward/Left turn/Right turn /Reverse 25 pcs. 8. Confirm no Hand effect at control distance Touching Antenna with Hand. Control distance 50 %) 25 pcs. 9. Confirm the range meet the spec 6 meters 25 pcs. 10. Confirm both 49 MHz and 27 MHz versions and Channel A, B and C can be used together, with users side by side (as in a race, etc.) No interference/loss of range should occur 11. Confirm firmness of telescopic antenna Slightly over pull, extend amp。 Measurement 更多免費資料下載請進： 好好學習社區 Page 8 of 22 Master carton drop test cm (height) 12 pcs./carton Less than kg. 2 master cartons Individual inner box drop test cm (height) 5 boxes Vibration test X,Y,Z axes。 30 minutes per axes 1 carton Tape test on chrome plate, silkscreen, rubberized texture, sprayed paint Using 3M 810 scotch or rubber eraser 5 units Antenna tension test for transmitter unit 15 lb 5 units The Tank battery life test (fully charged) Limit 3 min, Nominal 5 min. 5 units Impact test Forward 15 times/Reverse 1 time 5 units Gear reliability/durability test Forward/Reverse gear change 25 cycles 5 units Jump test 2 inches and 20 times 5 units Stop tread / wheel tests and Motor stall test (2 inches) 20times 5 units Running drop test 30 inches on business carpet Climbing angle test 35 degree 5 units slope Battery patibility test on TX and Charger stand RadioShack, Duracell or Energizer 5 units Reverse polarity test on TX and Charger stand 1 minute (Built in 1 Diode) 5 units 2. Checking Packaging Refer to for details Master Carton Verify shipping mark correctness (Cat No/PO No./Destination/QA No.) Noticeable damage/torn/unfitness Confirm bar code readability by a bar code reader and correctness. Same as approved sample?s bar code No. Confirm the strength of seam strong enough Apply tearing test。 retract 35 times 25 pcs. Drop test, bare unit (controller and RC Vehicle), and confirm they still function normally afterwards. Using Vendor Specification for height requirement. 13 Units Verify manually moving the unit using varied force and confirm the unit still operates normally afterwards Simulates a child pushing the tank around freely without using the remote control. Use Vendor spec for applied force/ resistance info. Verify manually moving the unit?s turret and cannon using varied forces and confirm the unit still operates normally afterwards Simulates a child playing with the tank freely (without using the remote control.) Use Vendor spec for applied force/ resistance info. 更多免費資料下載請進： 好好學習社區 Page 11 of 22 Exercise removing the battery partment door, installing batteries and closing the partment door. Verify there is no damage/ intermittence to the partment door or battery terminals afterwards. (Stand, Controller, and Tank if applicable) Exercise removing and reinstalling the tread to the drive wheels and confirm no damage to the tread afterwards. Simulates removing tread to clean debris from wheels/ track and also simulates children taking tread off. Exercise the controller joysticks and confirm there is no damage/ intermittence afterwards. Confirm connecting the tank to the charging base 25 times and verify the charging indicator es on each time. Verify there is no damage/ intermittence to either unit afterwards. Confirm replacing the battery within the tank unit and verify the unit functions normally and there is no damage to the unit afterwards. Use NiMH Battery this is only suggested due to not having the prosample or an Owner?s Manual to verify where the “BuiltIn” battery is replaceable. 13 Units 6. General test 100% units sampled In shield test room or cage Refer to page. 14 for details (All samples) 1. Check antenna tip secure and antenna mounting firmness Pull, Bend, extend, amp。 Straight Line (1meter) Car has a trimmer knob. Run Tank in L/R spins and figure 8 Conduct Forward/Reverse gear change Run impact test curb 4 times in each round Angle deviation is less than +/ 50 cm 2 times each round 10 times each round Forward, left turn, right turn, and reverse Endless Track must not e out of wheels. 14. Check Turret L/R turns mode. 15. Check Cannon and Machinegun modes to confirm sound e out of speaker on the Tank at 25 cm away from Tank?s Turret. Cannon 60 dbA Machinegun 60 dbA 16. The Endless rubber track must not easily e out of wheel mechanism. 17. Change channel switch “A, B and C” on TX and RX on both 27 and 49 MHz, and make sure the Tank can be used together with users side by side (as in a race, etc.) No interference/loss of range should occur 7. Checking Internal structure of the reliability amp。 RX ? Pulling force for tire/wheel on RX ? Battery surface temperature ? Battery running time (life) ? Wall stall (driving stall test) at forward function ? Tank speed ? Spin diameter left/right ? CIimbing angle test ? Control range test at Channel A, B and C on both 27/49MHz ? 10 hrs continuous running test Task to be pleted: Verify th