論船舶艙室設備底座焊接工藝規范-wenkub
2023-04-24 07:34:16 本頁面
【正文】 voltage . 設備底座上船安裝前應作好防繡漆，底座吊運上船后應妥善放置，并盡快安裝，不宜隨意亂丟，以防遺失、損壞。 Welding gun must have current volume and can be used for a long time , convenient operation to welder , feeding wire steadily . Crust of welding gun must have better insulated property . 4 人員 Personnel CO2保護焊的焊工必須經過專門培訓和考試，并按船級社合格證所規定之類別從事產品焊接。Don’t use it again when cylinder pressure is below 1 Mpa . 焊接設備 Welding equipment CO2氣體保護焊焊接設備應采用設備制造廠生產的專用設備，并應定期進行嚴格的檢測與維修。 should choose CJ507 low hydrogen Na coating C steel electrode or CO2 gasshielded arc welding . 。 The height of tack welding don’t exceed normal welds , eliminating postweld slag at once .，定位焊縫不宜過短，一般強度鋼為（30~40）mm，高強度鋼為50mm，焊縫厚為（3~4）mm。 Referring to document ≤QUALITY INSPECTION OF SHIPBUILDING ≥3 焊接前準備Preparation of forewelding CJ422鈦鈣型藥皮碳鋼焊條參數( CJ422 parameters for C steel electrode of Ti and Ca covering) (form)試驗項目(Test project)δs(Mpa)δb(Mpa)δ5(%)AKV（20176。The specification rules the requirements of forewelding to preparation , personnel ,technological requirements ,technology process ,examination 。n船舶艙室設備底座焊接工藝規范 WELDING PROCEDURE SPECIFICATION FOR EQUIPMENT BASE OF HULL CABIN 1which are for base of important equipments and mon equipments of hull cabin . 本規范適用于各類船舶艙室設備底座的焊接。）J≥330≥420≥22≥47X射線探傷(Radiographic inspection)：Ⅱ級（Grade two） 焊條直徑(MM) Diameter45焊接電流(A) Current60~110120~150160~210220~270 CJ507低氫鈉藥皮碳鋼焊條參數 (CJ422 parameters for C steel electrode of low hydrogen Na covering ) (form)試驗項目(Test project)δs(Mpa)δb(Mpa)δ5(%)AKV（20℃）J(30℃)≥400≥490≥22≥47≥27X射線探傷(Radiographic inspection) Ⅱ級（Grade two） 焊條直徑(MM) Diameter45焊接電流(A) Current60~110120~150160~210220~270210~260 焊前施工人員應先了解被焊工件的施工要求及作業環境、鋼材牌號等級、據此按材料的選配原則確定焊條焊絲牌號、規格及極性。 The length of tack welds shall be longer because of making defects easily with CO2 gasshielded arc welding .Common strength steel (30—40)mm, high strength steel 50mm ,thickness of welds (3—4)mm . 所要焊接的設備底座已經按照裝配要求定位好，并且打磨焊前認可才能進入焊接階段。 May choose mon CJ422 C steel electrode of Ti and Ca covering for other monequipment base . 焊接材料 Welding consumable 焊絲： Welding wireCO2焊絲可選用直徑為（￠）mm的實芯焊絲或藥芯焊絲，并
公司管理相關推薦
鄂ICP備17016276號-1