車輛工程畢業設計-汽車abs檢測試驗臺機械系統設計(已修改)
2024-12-19 15:57 本頁面
【正文】 I 摘 要 ABS 是在汽車制動過程中提高操縱穩定性和轉向控制能力的主動安全裝置。 ABS正常工作對汽車行駛安全至關重要。滾筒式慣性檢測實驗臺是檢測汽車 ABS 系統性能的實驗臺，它可以替代路測，實現 ABS 測試系統在室內測試的要求。滾筒式慣性檢測實驗臺主要有三部分組成，電機驅動部分、滾筒轉鼓部分、飛輪組部分，本文主要針對其各部分的結構進行設計的。 本文介紹了 ABS 系統滾筒式慣性檢測實驗臺主要部件的設計方法及設計過程。論述了 ABS 系統的工作原理，分析了現在存在的各種汽車性能檢測實驗臺，確定了總體設計方案及各部分零件的 型號的選取。本文 ABS 系統滾筒式慣性檢測實驗臺 采用滾筒帶動車輪轉動，同時根據車輪的尺寸及汽車的重量分析設計滾筒的結構及尺寸。 ABS系統滾筒式慣性檢測實驗臺 主要采用飛輪模擬汽車在道路上行駛的慣量，根據模擬的原理對飛輪進行分析計算，確定飛輪的數量及結構尺寸，并且對實驗臺進行一定的校核 。最后使用 AutoCAD 進行平面制圖。 全套圖紙，加 153893706 關鍵詞 ： ABS 系統；飛輪；滾筒；實驗臺；轉動慣量 II III ABSTRACT ABS in the auto brake process improve handling stability and steering control ability of active safety device. ABS normal work is crucial for automobile driving safety. Rollertype inertial testing experiment platform is testing the car ABS system performance test rig, it can replace the road test, realize ABS test systems in indoor test requirements. Rollertype inertial testing experiment platform is made up of three main parts, motor drive part, roller drum part, fly wheel part, this article mainly aims at the structure of its parts design. This paper introduces the ABS system rollertype inertia detection experiments of the main parts of machine design method and design process. Discusses the working principle of the ABS system, analyzes the existing of auto performance testing experiment platform, determine the overall design scheme and various parts of the type of selected. This paper ABS system inertial testing experiment platform adopt cylinder cylinder driving wheel rotation, and based on the size and weight of the car analysis and design of roller structure and size. ABS system rollertype inertial detection experiments Taiwan mainly USES the flywheel simulation cars in road, according to the principle of rotary inertia of the flywheel simulation is analyzed, the quantity and structure to determine the flywheel of size, and experiments Taiwan perform some of the check. Finally using AutoCAD for plane drawings. Key words:ABS system。 The flywheel。 Roller。 Experimental stage。 inertia IV 目 錄 摘要 ....................................................................I Abstract ..............................................................III 第 1章 緒 論 ..........................................................1 概述 ..............................................................1 汽車 ABS 系統概述 .............................................1 ABS 性能檢測試驗臺的原理 .....................................2 ABS 性 能檢測試驗臺設計的要求 .................................2 ABS 性能檢測試驗臺設計方案的確定 ...................................2 ABS 性能檢測試驗臺整體方案的確定 .............................2 滾筒方 案的確定 ..............................................4 飛輪方案的確定 ..............................................4 本章小結 ..........................................................5 第 2章 實驗臺部件的選擇 ..............................................6 電機的選擇 .........................................................6 電機功率的計算 ..............................................6 驅動元器件的選擇 ............................................6 聯軸器的選擇 ......................................................7 軸承的選擇 ........................................................8 軸承載荷的計算 ..............................................8 軸承型號的選擇 ..............................................9 本章小結 ..........................................................9 第 3章 滾筒設計 ......................................................10 概述 .............................................................10 滾筒結構分析 .....................................................10 滾筒尺寸的選擇 ....................................................11 本章小結 .........................................................13 V 第 4章 飛輪設計 ......................................................14 概述 .............................................................14 飛輪轉動慣量分析 .................................................14 飛輪結構分析 ......................................................15 飛輪計算 ..........................................................16 本章小結 .........................................................18 第 5章 總體設計與校核 ...............................................19 概述 ......................
公司管理相關推薦
鄂ICP備17016276號-1