空調公司1101檢驗測量和試驗設備控制程序(已修改)
2025-07-29 18:43 本頁面
【正文】 程 序 文 件 Procedure Document 重慶英特空調有限公司 Air International Chongqing Co., Ltd. 文件名稱 (Doc Name):檢驗測量和試驗設備控制程序 Inspection, Measuring amp。 Test Equipment Control Procedures 版次 Ver 頁次 Page 發行日期 Release Date 文件編號 (Doc No)： AICQ/QP1101 B/0 1 7 20xx0110 1 目的 Objective 對檢驗、測量和試驗設備以及整個測量系統進行控制、校正和維護，保證其使用時不確定度已知 ,并與所要求的測量能力相一致。 This is to control, calibrate and maintain the inspection, measuring and test equipment as well as the whole measurement system, so as to ensure the uncertainty degree is known during usage and is the same to the measuring capability required. 2 適用范圍 Applicable Scope 適用于證實產品符合規定要求的檢驗、測量和試驗設備（包括檢具）以及整個測量系統的控制。 This is applicable to the control of inspection, measurement amp。 test equipment (including calibration equipment) and the whole measurement system that are used to prove if the products conform to the requirements. 3 職責 質量部負責檢驗、測量和試驗設備的校驗以及測量系統分析。 The Quality Department is responsible for the calibration of the inspection, measuring and test equipment as well as the analysis of the measurement system. 技術工程部對檢驗、測量和試驗設備的適用性負責。 The Engineering Department is responsible for the applicability of the inspection, measuring and test equipment. 采購物流部負責檢驗、測量和試驗設備（以下簡稱檢測設備）的采購。 The Purchase amp。 Logistics Department is responsible for the procurement of the inspection, measuring and test equipment (hereinafter short as IMTE). 各使用人員正確使用檢測設備，并負責日常保養工作。 All users should use the IMTE correctly and be responsible for the daily maintenance. 4 工作程序 Work Procedures 選購與制造 Purchase and Manufacture 程 序 文 件 Procedure Document 重慶英特空調有限公司 Air International Chongqing Co., Ltd. 文件名稱 (Doc Name):檢驗測量和試驗設備控制程序 Inspection, Measuring amp。 Test Equipment Control Procedures 版次 Ver 頁次 Page 發行日期 Release Date 文件編號 (Doc No)： AICQ/QP1101 B/0 2 7 20xx0110 質量部根據測試產品 /過程質量特性要求，得出最大允許的測量不確定度和儀器的環境條件，在此基礎上提出請購申請，寫明添置原因、用途、設備型號、規格、性能參數要求等，經管理者代表審核，總經理辦公室核準后交付采購物流部采購。 The Quality Department will measure the maximum allowable uncertainty and the environment condition for the instrument based on the requirement of test product/process quality characteristics. The application will be put forwar
公司管理相關推薦
鄂ICP備17016276號-1