基于usb接口的單片機與pc機通信-論文(已修改)
2025-11-23 15:02 本頁面
【正文】 基于 USB接口的單片機與 PC機通信 摘 要 ： 安裝 USB設備不需要用戶自己設置硬件與軟件的選項， USB接口的傳輸速度要比計算機傳統的串行口和并口快的多，所以 USB設備已經廣泛應用。由于協議的復雜性，在系統中實現 USB主機功能的實例還不是很多。因此本文沒有從復雜的 USB總線協議入手，而是選擇了南京沁恒公司出產的 USB接口芯片 CH375。 其具有內置固件模式和可編程的 2311外部固件模式，可以根據需要任意選擇工作模式。 關鍵詞： 單片機； CH375； USB；協議 The Design of the munication between MCU and PC which is based on USB interface Abstract: USB device does not require users to install their own set of hardware and software options, and puter transmission speed faster than the traditional serial and parallel port , so USB devices have been widely used. Because of the plexity of the agreement, in the system of USB host function realization example is not a lot. Therefore this article does not starting with the plex USB agreement, but chose the USB interface chip CH375 which produced by Nanjing Qin Heng pany, their model has a builtin firmware and firmware programmable of 2311 external model, we can choose the mode of operation with a need for arbitrary. Key words: Single Chip Microcontroller。CH375。USB。Agreement 目 錄 1 前 言 .......................................................................................................................................1 題目的來源與開發意義 ...................................................................................................1 系統功能概述 .................................................................................................................1 2 系統硬件設計 ...........................................................................................................................2 方案論證 ........................................................................................................................2 系統硬件總體設計概述 ...................................................................................................2 系統功能概述 .................................................................................................................3 系統各模塊的設計 ..........................................................................................................4 單片機控制系統 ....................................................................................................4 USB 接口模塊 .......................................................................................................6 3 系統軟件設計 ......................................................................................................................... 11 系統軟件總體設計思想 ................................................................................................. 11 各功能模塊軟件程序設計 .............................................................................................. 11 4 系統調試 ................................................................................................................................ 16 硬件電路調試 ............................................................................................................... 16 各功能模塊軟件調試 ..................................................................................................... 16 5 結論 ....................................................................................................................................... 18 參考文獻 ..................................................................................................................................... 19 致 謝 .......................................................................................................................................... 20 1 前 言 題目的來源與開發意
畢業設計相關推薦
鄂ICP備17016276號-1