變頻器設計使用參考外文翻譯(已修改)
2025-01-28 11:40 本頁面
【正文】 河南理工大學萬方科技學院本科畢業論文河南理工大學萬方科技學院電氣與自動化工程系2012屆畢業生英文文獻專業： 電氣工程及其自動化 班級： 08電氣6班 學號： 0828100023 姓名： 葉國印 時間： 2012 年 5 月 31 日 外文資料與中文翻譯外文資料：Converter reference design(1) Converter Selection: Selection to determine the frequency converter when the following points: 1) The purpose of a variable frequency。 constant pressure to control or constant current control. 2) the load converter types such as leaves or pump volume pumps, with special attention to load the performance curve, the performance curve of the decision of the ways and means. 3) the frequency converter and load matching Voltage match: a rated voltage converter with a rated voltage line with the load. Current matches: ordinary pump, the rated current inverter and motor rated current match. For special load such as deepwater pumps, and so on need to refer to the electrical performance parameters to determine the most current inverter current and Guozainengli. Torque match: in this case constant torque load or slow down when the device may have occurred. 4) the use of highspeed motor drive inverter, because of the highspeed motor, antismall, high harmonics lead to increased output current value increases. So for highspeed motor inverter Selection, its capacity to be slightly larger than the ordinary motor selection. 5) If the frequency converter to a long cable run, this time to take measures to curb the long cable to the impact of capacitive coupling, inadequate efforts to avoid converter, so in this case, the drive to enlarge the capacity of a file or the converter Output installed output reactor. 6) For the application of some special occasions, such as high temperatures, high altitude, at this time would cause the down converter capacity, the drive to enlarge the capacity of a block. (2) inverter control schematic design: 1) First confirmation of the installation environment Converter Operating temperature: highpower converter is the internal electronic ponents, vulnerable to the effects of temperature, product general requirements for 0 ~ 55 ℃, but in order to ensure the safe, reliable, the use of room to be taken into account, the best control in 40 ℃ below. In the control box, the converter box should generally be installed in the upper and strictly ply with the Manual of installation requirements, absolutely not be allowed to heating elements or ponents easily fever close to the converter installed at the bottom. Ambient temperature: the temperature is too high and large temperature changes, within easy converter there is dew, the insulation properties will be greatly reduced, or even shortcircuit caused the accident. When necessary, to be added to the desiccant in the box and heater. In water treatment, generally heavier than water vapor, if the temperature changes, then this problem would be more prominent. Corrosive gases: the use of the environment if the corrosive gas concentrations, will not only lead corrosion of ponents, printed circuit boards, but it will also accelerate the aging of plastic devices, reducing insulation properties. Vibration and shock: the control cabinet with converter by vibration and mechanical shocks will cause electrical connection is bad. Huaian thermoelectric there such a problem. Apart from raising the control cabinet at this time of the mechanical strength, vibration and shock away from the source, we must also use seismic rubber pad fixed within and outside the control cabinet, such as electromagnetic switches have a vibration ponents.
環評公示相關推薦
鄂ICP備17016276號-1