【正文】
1 寬帶直流放大器的設計與實現 宋加磊 1,潘克修 2,夏緒超 3 ( 4 隊,江蘇 南京 210007; ; 3 隊,江蘇 南京 210007) 摘 要 :本系統 采用 80C51 單片機作為 寬帶直流放大器電路 的控制芯片,采用 VCA810 組成的放大電路對輸入的小信號進行智能的放大 , 既可以通過電位器來宏觀的調整放大增益,也可以通過鍵盤精確的設定放大增益, 設置步進等級可達 1dB。 輸出的結果準確的顯示在 LCD 上, 整個系統 輸 出 穩定 ,數控簡單可靠。 關鍵詞 : 程控放大器 ; 寬帶;直流; VCA810 中圖分類號 : TN912 文獻標識碼 : B 文章編號 : Design and Realize of Widthband DC Amplifier SONG Jialei1,PAN Kexiu2,XIA Xuchao3 ( Team 4 ICE,PLAUST,Nanjing 210007,China。 of Electronic Information Engineering ICE,PLAUST。 Team 3 ICE,PLAUST,Nanjing 210007,China) Abstract: This design uses 80C51 as a microputer control chip to make a broadband directcurrent amplifier circuit, using an amplifier circuit posed of VCA810 to amplify a small input signals in an intelligent way. It not only adjusts the amplification gain through the potentiometer, but also accurately sets the amplifier gain via the keyboard as low as 1dB, and at the same time the results of the output are accurately displayed at the LCD. It’s good at a stable output and a simple and reliable numerical control. Key words: procedure control amplifier。 widthband。DC。VCA810 1 系統介紹 本系統 是 以 80C51單片機為控制芯片 ,輔以合適的信號放大電路,峰值檢波電路和人機交互電路構成的 高速 寬帶直流放大器, 簡潔的實現了 對 交直流 小信號 (不大于 20mV)進行放大, 即輸入信號不 只局限于 交流,亦可以是直流 電壓 。 本 系統 的最大放大倍數可以達到 60db,帶寬為 10MHz,是一個性能非常好的寬帶放大器。 系統結構圖 如圖 1所示。 信號放大電路 峰值檢波電路 單片機 輸出 圖 1 寬帶直流放大器總系統圖 輸入 LCD 顯示 鍵盤 功率 放大電路 D/A A/D 2 其中: 頻帶選擇通道 采用 LC 低通濾波器實現頻帶選擇 ;信號放大電路采用 TI 公司的三種高速運算放大器 OPA84 VCA810和 THS3001構成直接藕合程控放大器; 數字 AGC控制由峰值檢波、 A/D、單片機控制器 和 D/A實現帶內增益控制 ; 功率放大電路實現輸出電壓放大與功率放大,提高負載能力;整個放大器的控制 采用傳統 8051作為控制核心。顯示使用液晶顯示屏顯 示控制選擇方式及輸出效果。 2 系統方案選擇與論證 系統基本方案 根據設計任務的功能要求 ,