【正文】
XXXXX 學院 畢業設計論文 作者 學號 系部 專業 題目 指導教師 評閱教師 完成時間: 年 月 日 2 畢業設計 (論文 )中文摘要 (題目 ): 基于單片機的敲擊式語音門鈴 摘要: 敲擊式語音門鈴摒棄了傳統的按鈕觸發方式 ,當來訪客人習慣性地用手敲三下房門時 ,它便自動發出“叮咚 !”聲。這種門鈴巧妙地解決了使用普通門鈴時須在房門 (尤其是鐵制門 )上打孔、固定安裝按鈕開關的麻煩和不便 ,從而杜絕了他人故意破壞按扭開關等現象。該門鈴新穎而實用 ,具 有推廣價值。本論文設計采用單片機 AT89C1051 作為中心控制部分芯片,利用集成芯片 LM324 對振動傳感器信號進行處理、模擬輸出“叮咚!”音頻信號,使用 LM386 對輸出信號進行發大驅動喇叭發音。此外,本設計也可以采用語音集成芯片,利用單片機輸出管腳的電平值控制音頻輸出。還可做成報警設備等多種用途的語音系統。 關鍵詞 : 單片機 AT89C1051 振動傳感器 LM324 LM386 3 畢業設計 (論文 )外文摘要 Title : PERCUSSION VOICE DOORBELL BASED ON MCU Abstract: Percussion voice doorbell has discarded the traditional trigger manner, when the visiting guests used to knock the door three times, it will automatically give the “Ding Dong! sound. This doorbell sol ve the trouble and inconvenience of the use of ordinary doorbell skillfully, the problems include that the door have to be holed (especially iron door), and have the button switch fixed installed. Accordingly putting an end to the phenomenon such as the intended breakage of others, etc. It’ s innovative and practical with the popularize value. This paper design use the MCU AT89C1051 as the central control chip, process the vibrated sensor signal with the use of integrated chip LM324, simulate output the audio signal as “Ding Dong! sound, and make the use of LM386 to amplify the output signal and drive the loudspeaker. Furthermore, this design can also use voice integrated chip, using the levels from SCM output pins to control audio output. We may also produce allpurpose voice systems such as alarm equipment. keywords: MCUAT89C1051, Vibration sensor, LM324, LM386 4 目錄 1 引言 2 系統設計 設計要求 總體設計方案 3 硬件電路設計 電路設計 振動 傳感器介紹 LM324 的應用介紹 技術 電路 電路 LM386 應用介紹 揚聲器電路 4 軟件設計 AT89C1051 介紹 源程序清單 5 系統調試 結論 致謝 參考文獻 附錄一 元器件清單 附錄二 電路原理圖 5 1. 引言 敲擊式語言門鈴摒棄了傳統的按鈕觸發方式 ,當客人來訪習慣性地用手敲三下房門時 ,它便自動發出 叮咚 !的聲音。這種門鈴巧妙地解決了使用普通門鈴時須在房門 (尤其是鐵制門 )上打孔、固定安裝按鈕開關的麻煩和不便 ,杜絕了他人故意破壞按扭開關等現象 ,新穎而實用 ,具有推廣價值 .本論文設計采用 單片機AT89C1051 作為中心控制部分芯片,利用集成芯片 LM324 對振動傳感器信號進行處理、模擬輸出“叮咚!”的音頻信號,使用 LM386 對輸出信號進行發大驅動喇叭發音。本設計也可以采用語音集成芯片,利用單片機輸出管腳的電平值控制音頻輸出。還可做成報警設備等多種用途的語音系統。 2 系統設計 設計要求 一 .敲擊式門鈴的信號控制靈敏度要高; 二 .利用單片機的軟件程序消除誤抖動; 三 .信號放大濾波電路的運用。 . 總體設計方案 本設計分為三個組成部分:振動信號采集處理部分、 MCU 控制部分、語音信號輸出部分。 圖 1(總設計方案原理圖) 3 硬件電路設計 振動信號采集處理 單片機控制處理 語音信號輸出 6