【正文】
。 開鎖模條件: Mold opening parameter: 快速段中速度 低壓高壓速度 Highspeedmidspeed Low pressure high pressure speed 鎖模條件設定: Mold closing parameter setting 1鎖模一般分:快速→中速→低壓→高壓 Mold closing: highspeed →lowspeed →low pressure→high pressure ,如果是平面二板模具,快速鎖模段可用較快速度,甚至于用到特快,當用到一般快速時,速度設到5575%,完全平面模可設定到8090%,如果用到特快就只能設定在4555%,壓力則可設定于5075%,位置段視產品的深淺(或長短)不同,一般是開模寬度的1/3. In highspeed section, Mold closing speed depends on type of mold. For two –plate mold it can set quick and even especially quick usually, it set speed within 5575%. For fullplate mold it set speed within8090% while using especially high speed it set speed within 4555% and pressure within 5075% position distance setting differs depending on the volume of product and usually it can be set 1/3 of mold opening position. ,在快速段結束后即轉換成中速,中速的位置一般是到模板(包括三板模,二板模)合在一塊為止,具體長度應視模板板間隔,速度一般設置在30%50%間,壓力則是20%45%間. In midspeed section: Mold closing speed changes into midspeed after highspeed section finish. Midspeed start position is where two plates meet (include threeplate mold and twoplate mold ) Distance of midspeed is up to distance of two plates plate it speed within 3050% and pressure 2045%. ,低速設定一般是在模板接觸的一瞬間,具體位置就設在機臺顯示屏顯示的一瞬間的數字為準,這個數字一般是以這點為標準,即于此點則起不了高壓,高于此點則大,%25%,視乎不同機種而定,壓力一般設定于12%,有些機則可設于515%,也是視乎不同機種不同. Lowpressure section: Mold closing sets lowpressure when plates meeting. This position is set to the data of machine screen on this time. This point is the gage of the data. Data lower the point there is no highpressure. Data higher the point there is highpressure easily. It set speed within 1525% and pressure within 12% depending on type within 12% depending on type of injection molding machine. ,按一般機臺而言,高壓位置機臺在出廠時都已作了設定,相對來講,是不可以隨便更改的,大約在3035%左右,而壓力則視乎模具而定,可在5585%中取,比如完全平面之新模,模具排氣良好,甚至于設在55%即可,如果是滑塊較多,原來生產時毛邊也較多,甚至于可設在90%還略顯不足. Highpressure section: To normal injection molding machine, highpressure position had been set before they were sent to customer. It can not be modified. For example highpressure position of CHENHSONG machine is speed of highpressure section is about 3035% and higher than that of lowpressure. The pressure is up to mold, it can set within 5585% For fullplate mold, it’s eject air well, it can set pressure 55% .If mold has a lot of slides and flash rate high in production, pressure can set 90%. 加熱工藝條件設定 Heating technique parameter setting ,但卻必須遵循一個這樣的規則,. The proper temperature setting differs depending on type of resin material, but it must be abide by a rule that temperature setting should diminish in step