模具外貿葵花寶典-展示頁
2025-07-16 14:59本頁面
【正文】 )40. 加大拔模角，以便脫模順利 cavity is 2344 nitridng, the lifter and slider shelf is 728H. Please check the information above!23． 現在到了吃午鈑的時間，我們下午再繼續好嗎？It is time to have lunch, let39。 21． 我們將盡力達成你的計劃，如有異常，會及時通知你。We will try our best to plete your plan, if there are any plications, we will notify you immediately. ,試模注塑機型號為250噸,膠料顏色為黑色,產品外表面曬紋處理,、環保章、斜頂和行位座用738H，以上模具信息正確嗎？請確認！The length of this part is , Width is , height is 45MM, thickness is 2MM, weight is , the injection machine is 250T,the material is black, the outside of the part has texture, inner side needs polishing, and it also needs a date and recycle stamp,the coreamp。s discuss this project later this afternoon?(The undercut area interferes with the slide block and needs to be filled with material to help the slider move smoothly.)25. 加肉太多 (The thickness added is too thick.)26. 加肉面積太大 (The thickening area is too wide.) ( The gate position is moved.)28. 滑塊拆的位置 (The split line of slide block or the area of slide.)29. 此處有尖角，填充困難 (It is hard to fill this area due to the sharp feature.)30. 此處鋼材太薄，強度不足而且不容易冷卻(The strength of this area is too weak and it is hard to cool because the steel is too thin.)31. 圓柱特徵要有一半圓不可以拆在滑塊上，以免粘滑塊造成拉白，拉斷(We avoid designing the semicircle of the cylinder on the slide block because it will be pulled apart or cause drag marks.)32. 此處做斜銷在作動時會削到成品肉厚(The part will be damaged if we make the lifter in this area.)33. 這個面是裝配面，不能加料(This is a critical surface where we cannot add additional material.)34. 此處料位太厚，會有縮水，建議減料改善(Because of the shrinkage of the thickness, we suggest reducing some wall thickness to improve it.)35. 此面是不是外觀面，此處做滑塊的話會有夾線，是否可以接受(Please confirm whether it is a critical surface or not. Also, confirm whether it is acceptable to have a slide split line if we have a slide in this area. )36. 此處有倒勾，能否減料，使公母?？科疲蛔龌瑝K和斜銷(Please confirm whether we can reduce material to the area where we have an undercut as indicated to have shut offon cavity side. No slide block and lifter will be made. )37. 請盡快確認這種拆模方式和結構，否則會影響模期(Please confirm the issues of Parting line, Gate position...Etc. as soon as possible。 41. GATE做在此處的話有兩個缺點：。 therefore, we remend to have the Parting line as indicated.)45。 therefore, please confirm whether it can make undercuts, snatch pinsor leave coarse . on the core to snatch the part on)，成品表面會有應力痕，是否接受(Please confirm whether it is acceptable to have stress lines on the surface because the thickness is not equal.)47. 請注明何處為外觀面，能否提供2D圖和注意事項(Please advise where the critical surface is. Please also provide us a 2D drawing with critical dimensions. )48. 紅色所示處是有問題的地方，請?zhí)貏e注意(Please note the red highlights because those areas have problems.)49. 成品設計此處有問題，建議如下圖所示修改(We would suggest using the attached part design as the current design has problems.)50. 此處改為一個球形的凹槽 (We suggest modifying it as a globe recess.) 資料 個人短信 只看該作者 51. 圓柱特征要有一半不可以拆在滑塊裡，以防拉斷 (this issue is the same as )52. 此處大滑塊上走小滑塊，小滑塊要先退，大滑塊要做延遲(The inside small slide block will recede first and the parent slide block have to postpone sliding.)53. 滑塊要用液壓油缸抽芯以保証開合模順序(The slide pins will use
環評公示相關推薦
鄂ICP備17016276號-1