【正文】 1% 1 0,01 s 1 1 0,01 1 1 0,01 1 1 0,1 % Factory setting – – – – – – – – – – 0 Hz 70 Hz 5,00 s 5,00 s 0,00 s (off) 2,0 % 50 Hz 650 (off) – 2) 5 Hz 50 Hz 70 Hz 7 10,00 s 140 % 200 % (off) 8 2,00 s 7 2 1,00 4 27 4,00 2 0 0,2 % GB EnterParameter depending on power circuit GB 11 Operation of the Unit Password Input Ex works the frequency inverter is supplied without password protection, this means that all changeable parameters can be adjusted. After parameterizing the unit can be barred against unauthorized access (Passwords: see last but one page). The adjusted mode is stored. Barring the CPParameter Password ENTER UP GB FUNC ENTER Enabling the CP Parameter GB FUNC Password UP Operating Display The parameters below serve for thecontrolling of the frequency inverter during operation. Actual frequency display Display of the actual output frequency with a resolution of Hz. The operator displays additionally ?noP“ and ?LS“ if the control release or the direction of rotation are not switched (see ). The rotation of the inverter is indicated by the sign. Output frequency Hz, rotation forward Examples: Output frequency Hz, rotation reverse Set frequency Display of actually set frequency. The indication is done in the same manner as at . For control reasons the set frequency is displayed even if control release or direction of rotation are not switched. If no direction of rotation is set, the set frequency for clockwise rotation (forward) is displayed. Inverter status display The status display shows the actual working conditions of the inverter. Possible displays and their meanings are: no Operation control release not bridged, modulation switched off, output voltage = 0 V, drive is not controlled. Low Speed no rotation preset, modulation switched off, output voltage = 0 V, drive is not controlled. GB 12 Operation of the Unit Forward Acceleration drive accelerates with direction of rotation forward . Forward Deceleration drive decelerates with direction of rotation forward. Reverse Acceleration drive accelerates with direction of rotation reverse. Reverse Deceleration drive decelerates with direction of rotation reverse. Forward Constant drive runs with a constant speed and direction of rotation forward. Reverse Constant drive runs with constant speed and direction of rotation reverse. Other status messages are described at the parameters, where they GB occur. Apparent current Display of the actual apparent current in ampere. Apparent current / Peak value makes it possible to recognize the max. apparent current. For that the highest value of is stored in . The peak value memory can be cleared by pressing the UP, DOWN or ENTER key or over bus by writing any value you like to the address of . The switch off of the inverter also clears the memory. Utilization Display of the actual inverter rate of utilization in percent. 100% rate of utilization is equal to the inverter rated current. Only positive values are displayed, meaning there is no differentiation between motor and rege nerative operation. Intermediate circuit voltage Display of actual DC voltage in volt. Typical calues: Vclass 230 V 400 V Normal operation Over volt. () Under volt. () 300…330 V DC approx. 400 V DC approx. 216 V DC 530…620 V DC approx. 800 V DC approx. 240 V DC GB 13 Operation of the Unit Intermediate circuit voltage/Peak value makes it possible to recognize shorttime voltage rises within an operating cycle. For that the highest value of is stored in . The peak value memory can be cleared by pressing the UP, DOWN or ENTER key or over bus by writing any value you like to the address of . The switch off of the inverter also clears the memory. Output voltage Display of the actual output voltage in volt. GB GB Basic Adjustment The following parameters determine the fundamental operating data of the drive. They should be checked and/or adapted to the the Drive Minimum frequency With this frequency the inverter operates without presetting an analog set value. Internal limiting of the fixed frequencies …. Adjustment range: Resolution: Factory setting: 0...400 Hz 0,0125 Hz 0,0 Hz f UREF 0V 10V Maximum frequency With this frequency the inverter operates with maximum analog set value. Internal limiting of the fixed frequencies …. Adjustment range: Resolution: Factory setting: 0...400 Hz 0,0125 Hz 70 Hz GB 14 Operation of the Unit Acceleration time The parameter determines the time needed to accelerate from 0 Hz to 100 Hz. The actual acceleration time is proportional to the frequency change. 100 Hz –––––– x actual acceleration time = delta f Adjustment range: Resolution: Factory setting: 0,00...300,00 s 0,01 s 5,00 s f 100 Hz CP. 12 t Example: actual acceleration time = 5s。 B39。10 VDC 5 mA Voltage Output The voltage output serves for the setting of the digital inputs as well as for the supply of external control elements. Do no exceed the maximum output current of 100 mA. X2A 10 18 19 20 21 22 23 PE + . 24VDC / max. 100 mA GB 6 Installation and Connection Control Circuit BASIC 1 5 7 8 X2A 10 11 14 15 16 20 22 24 25 26 27 28 29 Assignment of Terminal Strip X2A Function + Set value input 1 Analog output 1 +10V Output Analog Mass Fixed frequency 1 Fixed frequency 2 Forward Reverse Control release/Reset 24VOutput Digital Mass Relay 1/NO contact Relay 1/NC contact Relay 2/NO contact Relay /NC contact Name AN1 Description Voltage input 0...177。10 VDC ^ 0...177。234。254。229。 206。242。235。238。229。228。241。240。229。238。255。229。226。225。 247。235。243。232。 1232。237。238。237。231。239。255。237。utilisateur doit se familiaris233。ssen jedem Anwender zug228。237。 STOP Erst Betriebsanleitung Teil 1 lesen ! Lisez d39。224。 239。ISTRUZIONE MANUAL DE INSTRUCCIO NES 208。239。239。247。234。instruction d233。 et de mise en garde de la partie 1. Les pictogrammes utilis233