【正文】 in lspexp 7 fc ef profile in exit egress remarking fc af 將af隊列的流標記為cs2和exp 2 dscpinprofile cs2 dscpoutprofile cs2 lspexpinprofile 2 lspexpoutprofile 2 dot1pinprofile 2 dot1poutprofile 2 exit fc be 將be隊列的流標記為be和exp 0 dscpinprofile be dscpoutprofile be lspexpinprofile 0 lspexpoutprofile 0 dot1pinprofile 0 dot1poutprofile 0 exit fc ef 5 dscpinprofile cs5 dscpoutprofile cs5 lspexpinprofile 5 lspexpoutprofile 5 dot1pinprofile 5 dot1poutprofile 5 exit fc h1 將h1隊列的流標記為nc1和exp 6 dscpinprofile nc1 dscpoutprofile nc1 lspexpinprofile 6 lspexpoutprofile 6 dot1pinprofile 6 dot1poutprofile 6 exit fc h2 4 dscpinprofile cs4 dscpoutprofile cs4 lspexpinprofile 4 lspexpoutprofile 4 dot1pinprofile 4 dot1poutprofile 4 exit fc l1 將l1隊列的流標記為cs3和exp 3 dscpinprofile cs3 dscpoutprofile cs3 lspexpinprofile 3 lspexpoutprofile 3 dot1pinprofile 3 dot1poutprofile 3 exit fc l2 將l2隊列的流標記為cs1和exp 1 dscpinprofile cs1 dscpoutprofile cs1 lspexpinprofile 1 lspexpoutprofile 1 dot1pinprofile 1 dot1poutprofile 1 exit fc nc 將nc隊列的流標記為nc2和exp 7 dscpinprofile nc2 dscpoutprofile nc2 lspexpinprofile 7 lspexpoutprofile 7 dot1pinprofile 7 dot1poutprofile 7 exit exit */策略：應用到網絡接口*/Config router interface pos5/2/1 port 5/2/1 QoS 100exit exitexitSAP口的分類和標記//對SAP端口入方向的流量打標記，其它未分類的數據在fc be中。當隊列的長度超過高限值時，丟棄所有到來的報文。set classofservice schedulers schDefault priority lowset classofservice schedulers schDefault transmitrate percent 20set classofservice schedulers schDefault buffersize temporal 20kset classofservice schedulers schDefault priority lowset classofservice schedulers schDefault dropprofilemap losspriority low protocol tcp dropprofile dropDefaultTCPset classofservice schedulers schDefault dropprofilemap losspriority low protocol nontcp dropprofile dropDefaultNonTCP//定義schDefault 為WFQ，帶寬分配20%，緩沖區大小為200000ms，并針對TCP和非TCP流量應用WRED策略。 如果路由器與本地NGN的BAC互聯，則對從NGN平臺進入的數據包的IP Precedence置為4；對進入NGN平臺的數據包不進行重新標記。B 為緩沖區長度。浙江電信城域骨干網以基于DiffServ 為主的QoS 技術（業務分類、標記、流量控制、隊列調度等機制）提供突發擁塞時QoS 保證。由DSLAM 、園區交換機實、ONU實現接入用戶上行流量的限速。建議初期采用寬裕帶寬預留的方式實現WRR調度。4 QOS配置模板 核心路由器配置 CRS1路由器配置 適用范圍n 軟件版本：n 硬件配置：現網CRS使用板卡均支持 配置說明n 使用模塊化(MQC)的QOS命令行方式實現，分別定義classmap和policymap以及應用servicepolicy) ；Classmap、policyma均為命名格式，采用匈牙利命名規則。定義優先級和業務等級的映射關系：diffserv domain default 8021pinbound 0 phb be green 8021pinbound 1 phb ef green 8021pinbound 2 phb ef green 8021pinbound 3 phb ef green 8021pinbound 5 phb ef green 8021pinbound 7 phb ef green 8021pinbound 4 phb af4 green 8021pinbound 6 phb af4 gree ipdscpinbound 0 phb be green ipdscpinbound 8 phb ef green ipdscpinbound 24 phb ef green ipdscpinbound 40 phb ef green ipdscpinbound 56 phb ef green ipdscpinbound 32 phb af4 green ipdscpinbound 48 phb af4 green mplsexpinbound 0 phb be green mplsexpinbound 1 phb ef green mplsexpinbound 2 phb ef green mplsexpinbound 3 phb ef green mplsexpinbound 5 phb ef green mplsexpinbound 7 phb ef green mplsexpinbound 4 phb af4 green mplsexpinbound 6 phb af4 green //入方向?qū)?biāo)記映射到內部業務等級ipdscpoutbound be green map 0 ipdscpoutbound af4 green map 32 ipdscpoutbound af4 yellow map 32 ipdscpoutbound af4 red map 32 ipdscpoutbound ef green map 40 //出方向?qū)I(yè)務等級映射到標記分類和標記：traffic classifier tcAny 配置通用流分類 ifmatch anytraffic behavior tbDefault 配置將數據流標記ipprecedence值為0策略remark ipprecedence 0traffic policy tpDefaultclassifier tcAny behavior tbDefaulttraffic behavior tbCritical 配置將數據流標記ipprecedence值為4策略remark ipprecedence 4traffic policy tpCriticalclassifier tcAny behavior tbCriticaltraffic behavior tbHigh 配置將數據流標記ipprecedence值為5策略remark ipprecedence 5traffic policy tpHighclassifier tcAny behavior tbHigh應用標記策略：int pos2/0/0 與163骨干互連的接口，對從163進入的流量清除優先級標記。sapingress 44 create description For h2 Ingress_Policy queue 1 create exit queue 11 multipoint create exit defaultfc h2 defaultpriority high exit sapingress 55 create description For ef Ingress_Policy queue 1 create exit queue 11 multipoint create exit