【正文】 m3℃～5℃for 2hour with no power on無包裝樣機，不通電，在3℃～5℃條件下放置2H，然后接通電源，應能連續正常工作1H High TemperatureStorage Test高溫保存試驗Naked sample with no power on is supposed to meet reliability specification form60177。 8 Mechanical Life Test壽命試驗 Item 項 目Specification 規 格Pick up feeding Mechanism 光頭進給機構After 200,000operation circles, sample is supposed to meet reliability specification() Voltage of feeding motor:DC2V One circle of operation: pickup at inner outer inner經過200，000次循環后，應滿足可靠性規格要求（）進給馬達電壓：DC2V一個動作周期：光頭在最內周 最外周 最內周Spindle motor主軸馬達Under standard condition,after 1000houre continuously playing, sample is supposed to meet reliability specification()在標準條件下，連續播放1000小時后，應滿足可靠性規格要求（）6． SAMPLING Examination抽樣檢查L(zhǎng)OT test adopts GB2828,Stipulate:AQL＝,IL＝2,usual two times sampling schemes.逐批檢查抽樣方案按GB2828，規定AQL＝，IL＝2，正常檢查二次抽樣方案。 High temperature, moisture, dust is supposed to be avoided機芯避免儲存在高溫、潮濕、灰塵多的地方 Extra pressure that can cause loader’ s deformation must be avoided 搬運時避免施加額外的壓力而造成機芯變形損壞； Static proof must be adopted during operation。2℃條件下放置2H，然后降至常溫，恢復16H，進行測定，應滿足可靠性規格要求 Low Temperature Storage Test低溫保存試驗Naked sample with no power is supposed to meet reliability specification in this case: suffered form30177。以下 TURN TABLE RUNOUT 端面跳動 ECCENTRICITY偏心 AXIAL LOAD耐壓負荷MIN 49N（5Kg） 49N（5Kg）以上BETWEEN TURN TABLE AND MOTOR SHAFT轉盤與馬達之間的耐壓力SLIPPING TORQUR打滑力距()()以上Disk Specification：Inner Diameter： 厚度： 4． Condition for performance Evaluation性能評價條件 Install Angle：Horizontal：177。400 rpm MinRated Load Rated VoltageRATED CURRENT額定電流105mA MaxRated Load Rated VoltageSTARTING TORQUE啟動轉矩,m MinRated VoltageNO LOAD SPEED空載轉速3500177。對本規格書產生疑義時,可依據與貴司的有關部門達成的協議解決。在滿足本規格書的范圍內，為改善產品性能可能會對硬件、軟件或制造工藝進行變更；2． General Specifications一般規格 Disc Loading Mode 進碟模式, motor driver front loading tray 馬達驅動方進倉 Disc fixing 碟片固定時Beam magnetic fixation 弱磁固定 Applicable Disk Diameter:支持碟片直徑 ：12厘米，8厘米 Regulate mode：3points regulate調整方式： 3點調整 Pick Up Driving Mode: Reduction Gear And Rack Drive光頭驅動方式：減速齒輪和齒條驅動 Feeding Ration: (Sled Motor Rotation One Circle)光頭移動量：（進給馬達旋轉一周） Pick Up Moving Range:177。200rpmNo Load，3VSTATING CURRENT啟動電流最大為245mA3V 5 TRAY IN/OUT MOTOR 進出倉馬達 ITEM 項 目SPEC 規 格REMARKS備 注RATED VOLTAGE額定電壓2V VOLTAGE RANGE 使用電壓范圍1～6 RATED LOAO 額定負荷4gcm RATED SPEED 額定轉速1600177。5176。 suffered form401