【正文】 9[2] [J] . 上海: 自動化儀表第　2003,24(3):2427 [3] 謝光忠、蔣亞東等. 2000,19(4):2933[4] :機械工業(yè)出版社,1993[5] 、系統(tǒng)配置與接口技術(shù).[6] 陳寶江,翟涌,.[7] 喻評，：化學工業(yè)出版社，2006[8] ：北京航空航天大學出版社。F increments? Temperature is read as a 9–bit digital value.? Converts temperature to digital word in 200 ms (typ.)? User–definable, nonvolatile temperature alarm settings? Alarm search mand identifies and addressesdevices whose temperature is outside of programmedlimits (temperature alarm condition)? Applications include thermostatic controls, industrialsystems, consumer products, thermometers, or anythermally sensitive systemDESCRIPTIONThe DS1820 Digital Thermometer provides 9–bit temperature readings which indicate the temperature of the device. Information is sent to/from the DS1820 over a 1–Wire interface, so that only one wire (and ground) needs to be connected from a central microprocessor to a DS1820. Power for reading, writing, and performing temperature conversions can be derived from the data line itself with no need for an external power source. Because each DS1820 contains a unique silicon serial number, multiple DS1820s can exist on the same 1–Wire bus. This allows for placing temperature sensors in many different where this feature is useful include HVAC environmental controls, sensing temperatures inside buildings, equipment or machinery, and in process monitoring and control.DETAILED PIN DESCRIPTIONOVERVIEWThe block diagram of Figure 1 shows the major ponentsof the DS1820. The DS1820 has three main data ponents: 1) 64–bit lasered ROM, 2) temperature and sensor, 3) nonvolatile temperature alarm triggers TH and TL. The device derives its power from the 1–Wire munication line by storing energy on an internal capacitor during periods of time when the signal line is high and continues to operate off this power source during the low times of the 1–Wire line until it returns high to replenish the parasite (capacitor) supply. As an alternative, the DS1820 may also be powered from an external 5 volts supply. Communication to the DS1820 is via a 1–Wire port. With the 1–Wire port, the memory and control functions will not be available before the ROM function protocol has been established. The master must first provide one of five ROM function mands: 1) Read ROM, 2) Match ROM, 3) Search ROM, 4) Skip ROM, or 5) Alarm Search. These mands operate on the 64–bit lasered ROM portion of each device and can single out a specific device if many are present on the 1–Wire line as well as indicate to the Bus Master how many and what types of devices are present. After a ROM function sequence has been successfully executed, the memory and control functions are accessible and the mastermay then provide any one of the six memory and control function mands. One control function mand instructs the DS1820 to perform a temperature measurement. The result of this measurement will be placed in the DS1820’s scratchpad memory, and may be read by issuing a memory function mand which reads the contents of the scratchpad memory. The temperature alarm triggers TH and TL consist of one byte EEPROM each. If the alarm search mand is not applied to the DS1820, these registers may be used as general purpose user memory. Writing TH and TL is done using a memory function mand. Read access to these registers is through the scratchpad. All data is read and written least significant bit block diagram (Figure 1) shows the parasite powered circuitry. This circuitry “steals” power whenever the I/O or VDD pins are high. I/O will provide sufficient power as long as the specified timing and voltage requirements are met (see the section titled “1–Wire Bus System”). The advantages of parasite power are two–fold:1) by parasiting off this pin, no local power source is needed for remote sensing of temperature, 2) the ROM may be read in absence of normal power. In order for the DS1820 to be able to perform accurate temperature conversions, sufficient power must be provided over the I/O line when a temperature conversion is taking place. Since the operating current of the DS1820 is up to 1 mA, the I/O line will not have sufficient drive due to the 5K pull–up resistor. This problem is particularly acute if several DS1820’s are on the same I/O and attempting to convert simultaneously.There are two ways to assure that the DS1820 has sufficient supply current during its active conversion cycle. The first is to provide a strong pull–up on the I/O linewhenever temperature conversions or copies to the E2 memory are taking place. This may be acplished by using a MOSFET to pull the I/O line directly to the power supply as shown in Figure 2. The I/O line must be switched over to the strong pull–up within 10 ms maximum after issuing any protocol that involves copying to the E2 memory or initiates temperature conversions. When using the parasite power mode, the VDD pin must be tied to ground. Another method of supplying current to the DS1820 is through the use of an external power supply tied to the VDD pin, as shown in Figure 3. The advantage to this is that the strong pull–up is not required on the I/O line, and the bus master need not be tied up holding that line high during temperature conversions. This allows other data traffic on the 1–Wire bus during the conversion time. In addition, any number of DS1820’s may be placed on the 1–Wire bus, and if they all use external power, they may all simultaneously perform temperature conversions by issuing the Skip ROM mand and then issuing the Convert T mand. Note that as long as the external power supply is active, the GND pin may not be floating. The use of parasite power is not remended above 100176。C in 176。C LSB, yielding the following 9–bit format:The most significant (sign) bit is duplicated into all of the bits in the upper MSB of the two–byte temperature register in memory. This “sign–extension” yields the 16–bit temperature readings as shown in Table 1. Higher resolutions may be obtai