外文文獻翻譯中英文對照電氣工程及其自動化專業電力系統通信蓄電池電源的檢測與維護解決方案-文庫吧在線文庫
【正文】 inly embodied in the voltage, resistance and capacity, the conventional detection method mainly measuring voltage, observe the shell signs, check the bolt tightness etc. So that only some representations to the parameter, and cannot master39。 Detection。 Filled, a quiet place 12 h, make a second check sex discharge, after the pletion of the discharge of battery charge。 由于殼體材料、氧復合效率、閥壓設計等綜合技術欠缺，有些電池池在充放電過程中，容易產生殼體變形、鼓包甚至裂縫。發現有電池達到 1． 8v時，立即中止測試。 閥控式鉛酸蓄電池生產對于技術工藝要求嚴格，目前國內電池生 產廠家有 300 多家，各種技術工藝品類繁多，建議在采購之前，對電池進行嚴格的篩選，盡可能選擇生產設備齊全、技術力量雄厚、服務配套完善的品牌企業。 對于柴油發電機的運行維護和管理，也應同蓄電池一起，納入專業化集中監控系統中來，以便及時掌握系統蓄電池電源的各項運行參數和工作狀態 。對于電池初驗的具體要求是：電池在投運前，首先進行第一次核對性放電，其容量應該不低于 95％，放電完畢后對電池進行充電；充滿后，靜置 1— 2h，進行第二次核對性放電，放電完畢后對電池進行充電 ；充滿后，靜置 1～ 2h，進行第三次核對陛放電，其容量應不低于 100％，放電完畢后對電池進行充電。 蓄電池的特征參數主要體現在電壓、內阻和容量上，常規的檢測方法主要測量電壓、觀察外殼體征、檢查螺栓緊固性等，這樣只能掌握一些表象參數，而不能掌握重要特 !參數如內阻、容量等。西北地區溫度變化較大 (一 30℃一 +55~C)，變電站通信機房較少配備空調，散熱性能較差，環境溫度對電池壽命形成直接影響。 關鍵詞 ： 蓄電池組；電源；檢測；維護 引言 電力通信系統各中心機房安裝配備有大量的蓄電池，其對通信系 統的運行與電能支撐、備用 起到重要的作用。 B. 2021 years urumqi power bureau telemunication room data show that because the battery electric power munication power supply fault from accidents accounted for 35%, in recent years the data interface rapidly, the ratio has risen to 7%. Two sets of data to show that the problem is more serious battery, the battery power supply of security and reliability have a serious threat, investigate its reason, mainly in the following nine aspects: battery design process quality The battery design process exists plate technology design, material design, oxygen posite design, the pressure set A prehensive plan defect, make a battery performance and life have been affected, main performance for battery failure, early leakage water loss, deformation cracks, etc. For simple ascending battery capacity, will the battery plate thin, and increase the number plate, makes the same volume of the casing electrolyte reaction area greatly increased, capacity improve soon, but because thin plate, plate easily corrosion, softening battery, service life and therefore greatly shorten, easy to produce the early failure problems. Because of the low pressure setting, charge once to a certain pressure, control valves will be open Rev., gas is through the valve were leaked, cause the battery fluid loss (usually in a hole or a column valve will find a slightly damp near the liquid), this kind of battery also easy to produce the early failure, valve pressure design and material also has a direct relationship between the shell. Due to shell material, oxygen posite efficiency, valve design pressure, and other prehensive technology lack, some batteries in the process of charging and discharging pool, easy to produce the shell deformation, beat even crack. the influ
研究報告相關推薦
鄂ICP備17016276號-1