freepeople性欧美熟妇, 色戒完整版无删减158分钟hd, 无码精品国产vα在线观看DVD, 丰满少妇伦精品无码专区在线观看,艾栗栗与纹身男宾馆3p50分钟,国产AV片在线观看,黑人与美女高潮,18岁女RAPPERDISSSUBS,国产手机在机看影片

正文內容

hy-5600b印刷體耐磨擦試驗機操作規范-文庫吧在線文庫

2025-08-26 17:14上一頁面

下一頁面
  

【正文】 with Some antirust oil to avoid rust. 簡易故障排除 Get rid of malfunction 按下面板電源開關機器無電 ,檢查機器后面板電源開關是否打開及電源線是否插緊, 如已插緊電源開關指示燈不亮,請拔出電源線插頭,用“一”字螺絲刀卸出保險絲盒,檢查保 險絲是否已熔斷,如已熔斷請在保險盒中取出備用保絲換上即可; Press the panel power switch and the machine is without electricity, then check if the Back panel power switch is turned on or the power line is plugged tightly. If all are ok but the indicator light still doesn’t shine, unplug the power line plug and unload The fuse box with “one” shape screwdriver to check if it has been fused. If yes, replace it with the spare fuse. 按下啟動鍵機器不運行, 檢查計數器是否已到設定次數,或調速器旋扭已調至最低 (慢)處以至于機器不運行,按下計數器“ RESET 復位清零”鍵或?qū)⒄{(diào)速旋扭調高 (快),機器即可運行; Press the start button and the machine does not run, then check if the counter reaches the set time or the speed screw is adjusted to the Lowest (slowly) location so that the machine doesn’t operate. Press the counter ” RESET” key or adjust the speed screw to a higher (quick) location. 運行時工作臺左右不等稱或時快時慢 ,請停止運行用內六角匙將偏心塊上之螺絲緊 過 即可 。 Open the tester power switch and adjust the rubbing distance to 520mm so that the weight wrapped with cotton can rub the test surface back and forth at a speed of / s. Remove the test units from left to right perpendicularly to the movement direction for total 50 cycles to finish the test. g. 接收標準: (本公司適用 ) Acceptable standard ( applicable to the pany) ★ 測試產品測試面 涂膜(鍍層) 變色,判定: NG。 Adjust the balance weight so that the pencil load added on the specimens is in a state of 0 and then tighten the screw so that the pencil to leave the test surface, fix the lever, add 177。反之, OK; The coating surface (plating) of the test products should not be discolored, if discolored: NG. On the contrast, OK. ★ 測試產品測試面涂膜 ( 鍍層 ) 脫落現象,如有 涂膜(鍍層) 脫落判定: NG。 It shows the grounding terminal. 技術規格 Technical specifications 荷 重 Load: 80g1000g 砝 碼 Weights: 50、 100、 200、 500g 各 2 個 2pcs for each 夾具自重 Tong deadweight: 80g 鉛筆角度 Pencil angle: 45176。 This item shows that If nonpliance, the operator may be injured. ! 警告 : warning 此顯示的項目 ,表示如不遵照 ,有可能損壞儀器。 This item shows that If nonpliance, the instrument may be damaged. 注意 : Notice 此顯示的項目 ,表示為有可能影響測試結果和質量。 測試材質 Test apparatus:橡皮擦、鉛筆 ( 2B 中華鉛筆 )、酒精 /棉布 ! ? ! ? 計 數 器 Cou
點擊復制文檔內容
公司管理相關推薦
文庫吧 www.dybbs8.com
備案圖鄂ICP備17016276號-1