【正文】 h crane shall not exceed 75% of rated lifting capacity. xii. 如需吊運工件行走時，載荷不得超過吊車的允許起重量；工件應處于吊車的正前方，離地不得超過500毫米，對于較長物件要防止擺動，緩慢行駛。All the workers have to wear appropriate PPE, such as protective clothing, protective mask, googles, insulating boots, safety helmet and so on.iii. 工人必須使用合適的呼吸保護設備，在有條件的情況下配備先進的焊接送風面罩。Flexible copper cable with waterproof rubber case satisfied the load requirements should be chosen as power line, besides, its properties should meet the relevant requirements of “Before starting works, the hot work permit must be applied as per the requirements of the owner . Fire extinguishers should be prepared in advance。 Construction areas should be cleaned to guarantee construction site safe, tidy and civilized. xxi. 作業人員應穩妥放置工具和材料，將邊角余料放到桶內，嚴禁向地面拋擲材料和工具。Construction machinery only could be used and managed by those authorized people or special people. Operators should ply with the relevant maintenance rules, and ensure them in good working conditions. vi. 操作人員中應按規定時間對機械設備運轉部件加注潤滑劑，開動前、工作前、工作中、停工后,均應按規定項目對各部位進行檢查，并應及時排除故障或提出修理意見。移動式施工機械在使用前應將移動輪子用墊塊擋住或 將底座固定牢靠。Except the seat stipulated in specification, do not stand or sit in machine. When the machine is running, do not touch the rotating parts.xiv. 重型機械設備需要通過架空線路、交叉路口、管架管廊時，應先調查了解，取得可靠數據，并經主管部門確認批準，方可通過。杜絕淘汰的和落后的非節能設備和材料的使用，積極采用技術成熟的新技術、新工藝，實現節能降耗，保護資源。Priority should be given to the use of ener。 It should backfill timely after formating precast pile holes, prevent personel falling into hole.ii. 現場蓄水池應用鋼管按照要求做好圍護，并設置警示牌。 foundation, lubrication level of rotating parts and flexibility of brake and clutch. Only qualified machine could be put into use. xiii. 除規定座位外，不得在機械的其它部位坐立。防護罩 應便于停車檢查和加注潤滑劑。 Only healthy people is authorized to operate construction machinery. iv. 操作人員不得擅自離開工作崗位，嚴禁把機械交給其他人員駕駛和操作。When conducting welding and cutting works, oil, flammable/explosive objects must be kept a safe distance, besides, fire fighting measures must be implemented while carrying out construction in those areas. xix. 工作結束或長時間離開作業地點，要關掉電焊設備的電源。Electric welder must be correctly earthed. Ensure to fix the earth line on the ground rod all the time, all the connections must be solid. xiv. 作業前，按照業主相關的規定要求辦理[動火作業許可證]。Some appropriate measures shall be taken to high frequency arc ignition parts of electric welder. There should be something insulated between the primary winding and secondary winding of welding machine. When welding works has to be conducted in dangerous places, such as metal sealedcontainer or humid environment, noload poweroff device of power supply must be equipped. ix. 及時修理、更換焊接/切割設備上不符合使用要求的零部件及電纜線，不允許在故障狀態下使用 焊接/切割設備。off the power , solid pile machine, must be moved to the flat place pile machine, the drill pole must slide into the ground to prevent accidental. 焊接作業的管理 Welding management i. 金屬焊接和切割作業人員必須符合特種作業管理規定的要求，持政府主管部門頒發的特種作業操作許可證上崗。Personnel must check with and without broken wires, wire rope fault phenomenon, if there is a hidden danger to immediately stop the construction, improvement after operation.xi. 在采用兩臺或多臺起重機械吊運同一重物時，應盡量選用相同機種和相同起重能力的起重機械并合理布置；明確起重作業總指揮和中間指揮人員，統一指揮信號。clothes.ii. 吊裝前，作好安全教育及安全技術交底工作，作好吊環、起重繩及起重機的檢查，發現問題及時解決。After Generator repaired, between rotor and stator slot must be carefully checked for tools, materials, and other sundry, lest damage the generator during operation.xii. 必須可靠接地。After the received signal parallel, the entire device shall prevail, adjust the speed, the synchronous closing moment.vii. 并聯運行的發電機應合理調整負荷，均衡分配各發電機的有功功率及無功功率。確認情況正常后，調整發 電機至額定轉速，電壓調到額定值，然后合上輸出開關，向外供電。 metal protecting net shall be equipped to lamp bulb。燈具與易燃物，且不得直接照射易燃物或應采取隔熱措施。Leakage protector should regularly start the leakage test button to jump test, proved to be normal is strictly prohibited to use.xv. 嚴禁使配電箱、開關箱的進線和出線承受外力。Power distribution cabinet and swith box should be equipped with lock, and be maintained by special people. viii. 電工應每日查、維修配電箱、開關箱，并做好記錄。 they also have to check the electrical device and protective facilities. Only qualified equipment could be put into use. ii. 定期測定絕緣電阻、耐壓強度、泄漏電流等絕緣性能，確保電氣設備和供配電線路絕緣良好。Special works, dangerous work and other works have to be carried out in accordance with the approved construction scheme. No unauthorized changes should be made.v. 進入施工現場應按照規定辦理臨時出入證手續，出入證件嚴禁轉借他人使用。ofSafety signboard or lables should be placed in somewhere bright. v. 安全標志牌的固定方式分附著式、懸掛式和柱式三種。焊接、切割作時佩戴防沖擊和熱輻射的防護面罩，在有引發危險可能時設置防護網或屏障。樁基施工安全方案(WMS)Work Management System中國化學CNCEC1. 安全保證措施 Safety Assurance Measures 正確使用各類勞動防護用品 Correct usage of PPEi. 進入施工現場作業人員一律穿結實的耐油底或鋼頭皮幫的防砸工作鞋。gloves and insulating gloves shall be equipped to welders and electricians, respectively. iv. 在有可能出現飛濺物體時如切屑、沖刷、撬、敲打等，佩戴防護眼鏡和圍巾。Safety signs and lables should not be set up on door, window or something movable which would make these signs hard to be found. Never place any barriers in front of signboard. iv. 安全標志牌和標簽應設置在明亮的環境中。typeThe construction area, working environment, facilities, equipment and tools shall be carefully inspected prior to construction. Once any hidden danger is found, conduct rectification immediately. iv. 特殊作業、危險作業及其它作業時，嚴格按照審批的方案組織施工，不得擅自改變方案，并根據作業需要到指定部門辦理各種施工“作業票”。Workers have to ply with the safe operation instruction, and wear the relevant PPE before using electrical equipment。Power distribution cabinet and swith box should be marked with name, function, and system wiring diagram. vii. 配電箱、開關箱箱門應配鎖、并應由專人負責。and wiring of power distribution box and swith box. xiv. 漏電保護器應定期啟動漏電試驗按鈕進行試跳試驗，試跳不正常時嚴禁繼續使用。It is unsuitable to only set up local lighting to a workplace. iii. 室外220V燈具距地面不得低于3米。If the portable lamp is used in humid environment, then something shall be guaranteed: housing and hand shank must be strong。Before starting , set the maximum valune of Magnetic force rheostat , di