【正文】 C. (See Note below)Cooling fanInside of unitTerminal blocks amp。s VF61 series inverter.Please read through this instruction manual carefully prior to using it and get familiar with properinstallation, wiring and operations to ensure optimum and troublefree operation.This instruction manual describes the basic and standard operation procedures. See the catalog forthe specifications, capacity, outer dimensions, environmental conditions and so forth.The VF61 series is to be used for a custom designed product or system, use the values written in thedrawings or test report of them, not the values shown in this manual.Precautions for Safe Operation1.2.3.4.5.6.7.8.Supply the specified voltage to the input terminals of the inverter. (If 400V power supplied tothe 200V type inverter, the inverter will be broken.)Provide the input side of the inverter with an MCB of the proper capacity.Be sure to connect the inverter to the ground to prevent accidents.Do not connect the supply line to the output of the inverter. Otherwise, the inverter will bebroken.Do not connect a phase advancing capacitor to the output terminals of the inverter.Otherwise, the inverter will be broken.Before maintenance work or inspection, turn the inverter power off to avoid electric shock.Wait until the CHG LED goes out. Note that the heatsink may be hot in some operatingconditions.Do not change the parts or make reckless alterations.The inverter has no noise suppression device. Please contact us if such a device is necessary.Memory protectionWe remend that set data be protected against rewriting in order to prevent misuse of the console.(See )Table of Contents1.Before starting operation supplied ponents and parts of unit construction and terminal wiring devices and wire sizesHow to use console the keys on console mode mode mode to protect dataAutomatic measuring motor data measuring operationsOperation procedures inverter to motor basic data from consoleTroubleshooting messages and operations failure of input power sourceInspection and maintenance inspection resistance test for replacing printed circuit boardAppendix dimensions wiring diagram unit dimensions specifications Programming chart (D61533) Input Signal Isolator Board instructions11235667991010111111121314151516161718192021262.3.4.5.6.7.1.Before starting operationChecking supplied ponents and parts.When you receive the VF61, check it carefully.(1) Make sure that the specifications of VF61, accessories and spare parts are properly inaccordance with your order. Check the logo mark on the cover to see if the unit type is asyou ordered.200V type: 22400V type: 44Voltage (V)Example: 2R2: 3R7: 5R5: 7R5: Inverter capacity (kW)Applicable power source INPUT: 380 to 460V, 3phase, 50/60 Hz OUTPUT: , (2) Make sure that the supplied VF61 hasn39。9 S D W T 195。 2)315AK20K203R744510AK20K205R54415AK20K207R5441030AK25K2011441550AK35K2515442050AK50K5022443075AK50K501430444075AK80K80141422374450100AK95K95142238454460100AK100K95223838554475125AK125K1253838607544100200AK180K150608010011044150300AK300K2208015020016044200400AK400K30015015025020044250500AK600K40020015025025044300600AK600K600250250150 (x2)Notes: values of the input MCB show the rated currents. (Determine the breaking capacity from the source capacity, etc.) shown values are those of the electromagnetic contactors MSK series made by Mitsubishi Electric Corp. wire sizes between the MCB and inverter input terminals are the sizes of the KIV or RD wires. cable length between the inverter and motor should be less than 30 meters. The shown values are those of the CV cables. the input MC is used, the interval between turning on and off should be more than 10 minutes.Safety Precautions the motor has a phase advancing capacitor, be sure to disconnect it. (If the inverter runs with the phase advancing capacitor connected, the inverter may be broken.) sure to connect a circuit breaker (input MCB) on the inverter input side. sure to connect the inverter and motor to ground. (Use the exclusive grounding terminal.)52.How to use console and Keys on ConsoleThe console has 16 columns x 4 lines LCD and operation keys as shown below.This mark designatesthat the console isselected to the numericentry key mode.LCDMode selector keysSelect the operation, function or monitor mode withthe OPR, FUNC, or MONIkey. (For details of thesemodes, see the followingsection.)^(Every press of keyalternates thesefunctions.Numeric entry keys(Upper)Function entry keys(Lower)Data setting keyReset key)Operation selectionkeys and operation keys. Monitor mode Press the MONI key, and the current setting is displayed as shown below. A monitor code (of 16 codes) and operation condition are displayed. (See for displayed items) Indicates selected operation keys. * MONITOR *REM/STOP/FOR/JOG (00)FOUT [Hz]Indicates a monitor code and its content.To change a displayed monitor code, press anumeric key (09), function entry key, and upor down arrow keys.Stored data (previous data) is displayed.After operation starts, an operation value isdisplayed. Displayed code list (Items selectable in monitor mode)Display on LCD000102030405FoutFrefIoutVoutTorq outVdc