【正文】 最重要的是在大規模生產的情況下，機器停機時間造成的損失，在生產高單位成本上升的必然結果。 ?+寬構思一個解決方案。 O 形圈是在插入耦合基礎元素和擴展驅動環蓋。 選擇不同的邵氏硬度 有一個彈性體插入不同邵氏硬度 98甲， 64 D 和 80 答：插入的選擇是最精確校準，以保證完美的耦合安裝。 自我調節錐部分擔保 1 磨損和維護的自由運作。 在比較的事實，很明顯的 R 和 W 開發和提供最緊湊的轉矩限制器可期。 該驅動聲，可感覺到動作，用來控制和關閉機器。 使用壽命是重要的要求，如無反沖，反應時間短，長期得到進一步優化。所以應選擇根據過負荷的原因能可靠的動作的方法 —— 組合復合方式，以實現全面的過負荷保護作用。 以上是出現超負荷的一些原因，對于這些原因產生的電機過熱現象應預先考慮到，并采取措施，防止過熱。通常閥門電動裝置采用限制轉矩的連軸器。 3．輸出軸轉動圈數：閥門電動裝置輸出軸轉動圈數的多少與閥門的公稱通徑、閥桿螺距、螺紋頭數有關，按 M=H/ZS 計算（式中： M為電動裝置應滿足的總轉動圈數； H 為閥門的開啟高度， mm； S 為閥桿傳動螺紋的螺距， mm； Z 為閥桿螺紋頭數。 2. Lockedrotor protection of motor thermal relay 3. Pairs of short circuit faults using fuse or overcurrent relays. Valve electric device to prevent overload of the right choice and is very much related and should pay attention to. In consideration of economic aspects limiting torques is a continuous challenge when developing Torque Limiters as an overload protection. The new generation of the backlashfree Torque Limiters. The new generation of the backlashfree Torque Limiters has been designed for being used in powertransmission and servo applications. Important requirements such as being backlashfree, short reaction times and long service life have been further optimized. The constructive benefit is ensured through fast availability of applications after a crash. For limited installations The further development and optimization of the already well established backlashfree Torque Limiter series SK has brought about an appropriate design for each application. The transmittable torques can be accurate defined and set. Even in regard to restricted installation space now, the couplings represent the latest stateoftheart. Areas of applications of the Torque Limiters ranging from to 2,800 Nm can be found in any type of mechanical dynamic drives are being continously improved by the use of preset Torque Limiters. When the overload occurs the Torque Limiters disengage in milli seconds. The movement of the Actuation ring can be sensed, and used to control and shut down the machine. Immediate availabillity of the machine after reengagement of the Torque Limiter can be assured. Increased economic efficiency Optimized disc springs and materials adapted to the use of the coupling allow for the pact and reliable design, better performance and wer mass. Also a long service life and maintenance free operation are importtant consierations when selecting couplings. Smaller couplings bined with a higher torque density additionally result in a cost advantage due to smaller dimensioning. On average the size of the Torque Limiter has been reduced by approx. 1/3 pared to other available products. This results in a reduced separation of masses in case of a crash due to the reduced weight and a smaller technical diameter. When paring the facts, it is clear that R + W develops and delivers the most pact Torque Limiters available period. A great variety The advantage of ball detent design Torque Limiters is the separation of the drive and the driven elements in milliseconds in case of an overload. Easy handling reliability are further advantages. Machine designs with little installation space or difficult to access areas do however often require special solutions. The R+ W range facilitates the easy modification by means of a modular concept. The hub type that is appropriate for the application is selected and integrated for the ideal design. The pressfit principle that has been developed by R+W uses the axial spring force of the metal bellows to pretension a t