【正文】 pdrlmonb Canned Drill Cycle mon call, before if gcode = 81, [ result = newfs (two, zinc) if drillcyc = three, drlgsel = fsg1(ss) + drillcyc * two else, drlgsel = fsg2(dwell) + drillcyc * two if initht refht, drillref = zero else, drillref = one prv_refht_a = c9k prv_refht_i = c9k ] z = depth prv_zia = initht feed = fr_pos prv_dwell = zero dwell p_moveb ment pcan prdrlout R drill position refht_a = refht refht_i = refht initht if absinc = zero, refht_a, !refht_i else, refht_i, !refht_a pdrill 鉆孔固定循環 pdrlmonb pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, dwell, *feed, strcantext, e p_movea ppeck 啄式鉆孔固定循環 pdrlmonb pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, *peck1, *feed, strcantext, e p_movea pchpbrk 斷屑固定循環 pdrlmonb pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, *peck1, *feed, strcantext, e p_movea ptap 攻螺紋固定循環 pdrlmonb pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, *feed, strcantext, e p_movea pbore1 鏜孔固定循環 1 pdrlmonb pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, dwell, *feed, strcantext, e p_movea pbore2 鏜孔固定循環 2 pdrlmonb pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, *feed, strcantext, e p_movea pmisc1 Canned Misc 1 Cycle pdrlmonb pcan1, pbld, n, *sgdrlref, *sgdrill, pxout, pyout, pfzout, prdrlout, shftdrl, dwell, *feed, strcantext, e p_movea pmisc2 Canned Misc 2 Cycle (User Option) pdrill pdrill_2 Canned Drill Cycle, additional points pdrlmonb pcan1, pbld, n, pxout, pyout, pzout, prdrlout, dwell, feed, strcantext, e p_movea ppeck_2 Canned Peck Drill Cycle pdrill_2 pchpbrk_2 Canned Chip Break Cycle pdrill_2 ptap_2 Canned Tap Cycle pdrill_2 pbore1_2 Canned Bore 1 Cycle pdrill_2 pbore2_2 Canned Bore 2 Cycle pdrill_2 pmisc1_2 Canned Misc 1 Cycle pdrill_2 pmisc2_2 Canned Misc 2 Cycle pdrill_2 pdrlcst 自定義鉆孔循環 8 19 (user option) Use this postblock to customize drilling cycles 8 19 pdrlmonb CUSTOMIZABLE DRILL CYCLE , pfxout, pfyout, pfzout, e p_movea pdrlcst_2 自定義鉆孔循環 8 19, additional points (user option) Use this postblock to customize drilling cycles 8 19 pdrlmonb CUSTOMIZABLE DRILL CYCLE , pfxout, pfyout, pfzout, e p_movea pcanceldc Cancel canned drill cycle result = newfs (three, zinc) z = initht prv_zia = initht pxyzcout !zabs, !zinc prv_gcode = zero pbld, n, G80, e Canned Text pcan Canned text before output call strcantext = sblank if cant_no zero, [ if cant_pos1 = zero, pcant_1 。/39。s39。 POST 名稱 : wgkG54 類型 : MILL 機床名稱 : GENERIC FANUC 控制器名稱 : GENERIC FANUC 描述 : GENERIC FANUC 3 AXIS MILL POST Associated Post : NONE 車 /銑復合 : NO 4axis/Axis subs. : NO 五軸 : NO 子程序支持 : NO 自動換刀 : NO 工作坐標系 : G54 Executable : MP 這個 POST支持 FANUC 控制器普通三軸銑床的 的 G 代碼輸出， 不支持自動換刀 ,有最大圓弧報警 它來源于 是針對 Mastercam Mill V8 的特征而設計的 歡迎各位試用此后處理程序 ,提供意見反饋 , 地址 : 福建漳州新華北路 56 號 力佳股份有限公司 吳桂凱 電話 : 05962931417 (19:0023:30) EMAIL: 修改日志 : Programmers Note: CNC 05/01/00 Initial post setup, jce 20201011 去掉自動換刀，吳桂凱 20201012 增加中文注釋，吳桂凱 20201021 增加最大圓弧警告，吳桂凱 20201105 修改坐標系為 G54，吳桂凱 特征 : 下列 Misc.(雜項 ) 必須使用整數 : mi2 絕對或增量坐標 at top level 0 = 絕對 1 = 增量 mi3 選擇 G28或 G30來執行參考點回歸 . 0 = G28, 1 = G30 Canned text: 在輪廓點里插入 cantext.以允許 /禁止 下列 Mastercam 里許可的功能， Entering cantext on a contour point from within Mastercam allows the following functions to enable/disable. Cantext 值 : 1 = Stop = 輸出 M00 停止碼 2 = Ostop = 輸出 M01 選擇停止碼 3 = Bld on = 在 NC 單節打開 單節刪除碼 (\) 4 = bLd off = 在 NC 單節關閉 單節刪除碼 (\) 鉆孔 : 在這個 POST 里支持所有的鉆孔方法 . 附加注意事項 : 1) G54 calls are generated where the work offset entry of 0 = G54, 1 = G55, etc. 2) 由 NCI變量 met_tool決定是否使用米制 3) 以增量方式從換刀起始位置計算運動量 . 起始位置通常定義為所有換刀時刀具所處的最后位置 Incremental mode calculates motion from home position at toolchanges. The home position is used to define the last position