【正文】 the pump。 。關開機器總電源 Switch (off and) on the machine。 安裝清除程序后有關清除的內容會在ergocontrol畫面中自動顯示出來 The special diagnostic program is automatically loaded into the ergocontrol. 具體的清除方法和內容由德馬格公司售后服務人員指導使用 Functions of the “DiagnosticDISK” are supported by the service engineer of DHT.警示：在圖Fig 14 中的“EERO：” 后若出現文件名時則表明磁盤出現或磁盤中的文 件有問題Attention: Here has some default with the disk or the relative stored in disk , if it a file displayed behind “ERRO:” when boot any disk 1. 2. 6 模具目錄磁盤/Diskette “MOULD CATALOGUE”所有已使用過的模具（產品）加工工藝（參數設定），均可通過機器備份到模具目錄磁盤上且當再次需要使用該工藝參數時可通過該磁盤重新載入機器。All machine settings (process parameters) can be stored at diskettes and loaded from the diskettes when necessary (see chapter 4. 5).，The drive unit uses 3,5 inch diskettes, High Density (HD), 1,44MB formatted.在機器畫面的45頁“模具目錄”中按軟鍵中的“磁盤工具”也可以在機器上將你的軟盤進行格式化By pressing the softkey “Disk Tools” on EC screen page “45 MOULD CATALOGUE” it is possible to format a disk on the machine too. 注意：此操作只有在機器未進行運轉時才能進行 Note： This function is possible only when the machine is not running. 警示：磁盤格式化將會將磁盤中原有的數據完全刪除Attention: Formatting a used diskette will destroy the original data. 1. 3 機器畫面/Screen Pages當打開機器電源時或選擇顯示器的“0 主菜單”時圖Fig15 畫面將呈現在顯示器中After switching on the machine or selection of EC screen page “0 MAIN MENU” the main menu is presented on the screen (see fig. 15). 畫面顯示/Screen Page Layout 在頁面的左上角所顯示的是正打開的密碼等級（從1級到5級）；In the left upper corner is presented the level of the input password (from one up to five).當密碼未被解開時在這個區域會出現一個地球圖標；When no password input is done, a globe is shown.同時這個區域也是光標所在的位置；At same time this field is the home position of the cursor.在畫面頂行中間位置是標示頁碼和該碼所在頁面的主菜單名稱，并且在有警報出現時也會在此區域以紅色的字體顯示工警報內容；in the middle of the headline are shown the number and the designation of the screen page and also alarm and fault indications (in red presentation).緊挨著的區域會顯示在自動可半自動生時的周期動作的進行情況（如：冷卻）和周期動作步驟中有時間控制的步驟的倒計時標示情況；Alongside of the designation is shown the actual stage of the machine cycle (. “cooling”) and the duration of this phase in count down.在畫面中輸入工藝參數時，正被輸入?yún)?shù)的最大允許輸入值和最小允許輸入值也會在該區域顯示；During the input of parameters is presented the allowed maximum and minimum value of the corresponding parameter.在畫面的頂行中的右上角所標示的是日期和時間；In the right upper corner are shown date and time在每個畫面的主要內容部分是顯示畫面的主要參數和供操作人員設定和改變的參數；The main part of each screen is foreseen for presentation of machine parameters, fortheir input and observation.在頁畫的底行是“軟鍵行”；The bottom line is called “softkey line”.在此行底下的軟鍵能激活同一功能組中的其它畫面或激活所選取畫面的其它功能；By means of the softkeys below this line can be called up other screen pages inside of the function group or can be activated functions belonging to the select page.在顯示器頁面中的“0 主菜單”頁中，可供將所有機器頁面轉換成黑白或反色顯示方式（“黑白顯示”、“反色顯示”、“正常顯示”）來顯示，并且在此頁面中也可調節顯示器的對比度（“對比度增加+”，“對比度減弱 –”“正常對比度”）； On EC screen page “0 MAIN MENU” can be selected the black and white or invers presentation of all pages (“Display bl./white”, “Display inverse”, resp. “Display normal”) and can be changed the contrast of the screen pages (”Contrast +“ ,”Contrast “and “Normal Contrast”).顯示畫面的選取/Screen Page Selection這里提供了幾種選取畫面的方法：There are different possibilities of screen page selection:通過熱鍵（功能組鍵）選取功能組鍵的主畫面，然后在功能組的主畫面中通過軟鍵選取其它畫面； Selection of function group by means of “hot key” (function group key) and selection of additional pages inside of the group by using the softkeys 在光標的初始位置輸入相應機器頁面的頁碼后按確認；Input of the screen page number when the cursor is in home position or通過熱鍵“i”或按頁碼“080”（光標要返回其初始位置）選取顯示機器頁面的“80 頁面清單”，然后移動光標至你所要進入頁面的頁碼上按確認鍵即可； Selection of EC screen page “80 PAGE LAYOUT” via function group key “i” orinput of the number “080” (when the cursor is in home position), selection of therequired page by moving the cursor to the screen page number and pressing theenter key “E”.注意：通過光標移動方向鍵移動光標會與光標快速移動滑輪移動光標可達到同樣的目的 （看 圖fig. 1—1）。Note: The cursor can be moved by the cursor move keys as well as by the shuttle wheel (see fig. 11).1. 4 頁畫列表/Screen Page layout機器所有頁面都會在顯示器的“80 頁面清單”列示出來（看圖Fig6）An overview of all screen pages is shown on EC screen page “80 PAGE LAYOUT” (seefig. 16).這一頁面也可通過按功能組鍵“i”(或直接在光標初始位置輸入080)翻到。It can be called up by pressing the function group key “i” (or by input the number “080”,when the cursor is in home position).通過在這一頁面上移動光標至相應的頁碼上，然后按確認鍵即可翻到你所要進入的畫面From this page every other screen page can be selected by moving the cursor to thescreen page number and pressing the enter key “E”.所有的頁面也可通過在光標初始位置直接輸入頁碼進入Every screen page can also be selected by input of the screen page number when thecursor is in home position.Fig. 16: EC screen page “80 PAGE LAYOUT”下圖所列出的是所有頁面所歸屬于功能組鍵的清單（圖fig17）An overview of all available screen pages is also shown at the scheme of the menustructure (see fig. 17). Pan Zhenyue 第 73 頁 Demagplastics Group 機器操作原理 培訓資料 德馬格塑料機械（寧波）有限公司 Fig 17 Menu Structure of the Ergocontrol 機器配置/Machine Configuration在機器畫面的“0 主菜單”頁面中按與“機器配置”相對應的軟鍵就可進入這一畫面（圖fig 1—8）By pressing the softkey “Machine” on EC screen page “0 MAIN MENU” is called up the EC screen page “1 MACHINE” (see fig. 18).在這一頁中會陳列以下內容：On this page are presented:。機器號碼（ Machine nr.”）,。 the machine number (”Machine nr.”),。機器型號(”M:”),。the machine size (”M:”),。機器所安裝螺桿的直徑 單位為mm (“Screw diameter”),。the diameter of the installed screw in mm (“Screw diameter”),。螺桿的驅動配置(”H:”),。the designation of the hydraulic screw drive (”H:”),。機器配置的電機功率，單位為KW/電源頻率單位為(“Drive”)。 the power of the machine drive in kW / the frequency in Hz (”Drive”),。機器配置油泵的輸出流量，單位為L/min(“P”),。 the volumetric rate of oil discharge of the pump in